| Post Name | Draftsman cum surveyor |
|---|---|
| Department | Mining & Geology:- English |
| Question Paper Code | 115/2014 |
| Date of Test | 5 August 2014 |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
‘The curvature of earth's surface, is taken in to account only if the extent of survey is more
than :
Answer
D. 260 sq. km.
2
‘The main principle of surveying is to work :
Answer
B. from whole to the part
3
A well conditioned triangle has no angle less than :
Answer
B. 30°
4
The imaginary line passing through the intersection of cross hairs and the optical center of
the objective, is known as :
Answer
Question Cancelled
5
A relatively fixed point of known elevation above datum, is called :
Answer
D. Bench mark
6
The boundary of water of a still lake represents :
Answer
C. Contour line
7
Closed contours of decreasing values towards their center, represents :
Answer
B. adepression
8
Toorienta plane table at a point with two inaccessible points, the method generally adopted,
is :
Answer
Question Cancelled
9
The smaller horizontal angle between the true meridian and the survey line, is known as :
Answer
A. Azimuth
10
The whole circle bearing of a line is 120°, its reduced bearing is :
Answer
B. S6&PE °
11
The most reliable estimate is :
Answer
C. Detailed estimate
12
Pick wp the item of work not included in the plinth area estimate :
Answer
Question Cancelled
13
The minimum width of a septic tank is taken as :
Answer
B. 75cm
14
For 100 sq. m. cement concrete (1 : 2: 4) 4 cm thick floor, the quantity of cement required, |
is :
Answer
Question Cancelled
15
According to ISI method of measurement, the order of the sequence is :
Answer
A. Length, breadth, height
16
Galvanising means covering iron with a thin coat of :
Answer
B. Zinc
17
For manufacture of stainless steel, steel is mixed with:
Answer
Question Cancelled
18
The commonly used raw material of cement is :
Answer
C. Lime stone
19
Age of a tree may be ascertained by :
Answer
D. Number of annual rings
20
For one cubic meter of brick masonry, number of bricks required is :
Answer
B. 500
21
‘The rocks formed from molten magma, are called :
Answer
C. Igneous rocks
22
A good quality stone absorbs water less than :
Answer
A. 5%
23
Reciprocal ranging is adopted when the following 1s encountered :
Answer
B. A hillock
24
If bearing of AB = 40 degrees and bearing of BC = 300 degrees, then angle ABC is:
Answer
A. 80 degrees
25
The magnetic bearing of a line is N 88° B. Its true bearing is S 89° E. Therefore, its magnetic
declination is :
Answer
B. SE
26
A freely floating needle slightly gets inclined to the horizontal anywhere except on the equator.
it is called :
Answer
A. Dip
27
Isogonic lines are the lines having the same :
Answer
C. Declination
28
An example for a level surface is -
|
Answer
D. Surface of a still lake
29
Invar tapes are made of an alloy of :
|
Answer
A. Nickel and steel
30
The least count of prismatic compass is :
Answer
B. 30"
31
ABCD is a square, bearing of AB=40°. Hence bearing of DC is:
Answer
A. 40°
32
A plumb line is:
Answer
Question Cancelled
33
Correction for refraction for a distance of 1 km=
|
Answer
Question Cancelled
34
Contour lines look to cross each other in case of :
Answer
D. An overhanging cliff
35
The box of Prismatic compass is made of :
Answer
B. Brass
36
If ‘n’ is the number of side, then the total sum of included angle of a closed traverse should
be:
Answer
C. (2n—4) 90°
37
In an internal focusing telescope, focusing is achieved by the movement of a lens which is
fitted inside the telescope and the lens is of the nature of :
Answer
D. Plano-Concave
38
Inrise and fall method, a complete check is provided on the calculation of :
Answer
D. All the sights
39
The working edge of an alidade, is known as :
Answer
B. Fiducialedge
40
The principle of ‘working from whole to part’ is used in surveying because :
Answer
C. Accumulation of errors is prevented
41
The correction of sag is: .
Answer
B. Always subtractive
42
The maximum tolerance in a 20 m chain is :
Answer
C. c) 5mm
43
A series of closely spaced contour lines represents
Answer
A. Steep slope
44
In which survey pacing is used for measuring the distances ?
Answer
C. Reconnaissance surveys
45
Two point problem and Three point problem are the methods of :
Answer
D. Resection
46
When a brick is cut in two halves longitudinally, one part is called : |
Answer
C. Queencloser
47
A vertical member supporting the hand rail is known as :
Answer
D. Baluster
48
Dog legged stair is
Answer
A. Half turn stair
49
Gypsum is added in cement :
‘
Answer
A. After burning
50
Increase in volume of dry sand when water is added is called :
Answer
C. Bulking
51
The indentation provided in a face of the brick is called : |
Answer
A. Frog
52
The standard size of the brick as per Indian standards is :
Answer
D. 19x9x9 em
53
The red colour obtained by the bricks is due to the presence of
Answer
C. Tron oxide
54
The aggregate is called course aggregate if it is completely retained on :
Answer
D. 4.75 mm sieve
55
The volume of one bag of cement weighing 50 kg is :
Answer
B. 0.0345 m3
56
The minimum water cement ratio to obtain workable concrete is :
Answer
A. 0.4
57
The solvent used in cement paint is :
|
Answer
B. Water
58
A badly mixed cement concrete may lead to :
Answer
D. Honey-combing
59
The approximate cost of the complete labour as a % of total cost of the building is :
Answer
Question Cancelled
60
Working out the exact quantities of various items of work is known as :
Answer
A. Quantity surveying
61
The approximate weight of one cubic meter of mild steel is :
Answer
D. 7850 kg |
A 9 115/2014
{P.T.O.] |
et ee
62
Which of the following is not a common size of reinforcement bars ?
Answer
B. 28 mm
63
The number of corrugations in a galvanized corrugated sheet is usually :
Answer
C. 10
64
The volume of cement required to prepare 100 cu.m. of 1: 2: 4 concrete is :
Answer
Question Cancelled
65
The weight of 10 mm diameter mild steel rod per meter length is equal to :
Answer
A. 0.62 kg
66
How many kilo-liters are there in one cubic meter ?
Answer
B. 1
67
The unit weight of R.C.C in kg/m’ is :
Answer
C. 2400
68
An area of one hectare is equal to :
Answer
A. 10000 m2
69
The amount required to be deposited by a contractor while submitting a tender is known
as :
Answer
D. Earnest money deposit
70
The minimum size of the pipe connected to septic tank is :
Answer
B. 100 mm
71
The technique of finding the fair price of an existing building or property is known as :
Answer
C. Valuation
72
In analysis of rates, the profit for the contractor is generally taken as :
Answer
A. 10%
73
The quantity of damp proof course
Answer
B. me
74
Thickness of plastering is usually :
Answer
B. 12mm
75
The unit of measurement for concrete work in R.C.C. is in :
Answer
Question Cancelled
76
The nominal thickness of an expansion joint in brick wall must be more than :
Answer
D. 40 mm
77
The angular steps used for changing direction of stairs are called :
Answer
C. Winders
78
‘The highest point of an arch is called as :
Answer
B. Crown
79
Inresidential building, the height of bath room should not be less than :
Answer
A. 24m
80
Lower edge of an inclined roof surface is called :
Answer
C. Eves
81
Inking post truss, the number of vertical post is :
Answer
B. E) One
82
True meridian passes through :
Answer
C. True north and true south
83
When the declination is negative, the magnetic meridian will be on which side of true |
| meridian ?
Answer
A. Western
84
Which of the following instrument is used for measurement of angles ?
Answer
D. Sextant
85
The length of ranging rod should be :
Answer
B. 2to3m
86
The first temporary adjustment to be done after setting up the plane table at any station will
be :
|
Answer
C. Centering and Levelling
87
lf the end stations of a line are free from local attraction, then the difference in between fore |
| ' and back bearing of that line should be ; |
|
Answer
A. 180°
88
A staff reading taken on a bench mark or change point is known as :
Answer
C. Back sight
89
The bench mark established by the Survey of India Department with very high precision
with reference to mean sea level is known as :
Answer
A. G.T.S. Bench Marks
90
Reading of the metric levelling staff can be taken accurately up to :
Answer
D. 0.005 m
91
Four sided figure having no parallel sides is called :
Answer
C. Trapezoid
92
The part of a circle bounded by an are and its chord is called :
Answer
B. Segment
93
An duodecagon has how many sides ?
Answer
D. 12 ;
94
Planimeter is used for measuring :
Answer
B. Area ;
95
Cross staff is used for :
Answer
A. Setting out right angles
96
Metric chains are generally available in : |
Answer
C. 20 mand 30 m length
97
The piece of brick cut with its one corner equivalent to half the length and half the width of
a full brick, is known as:
Answer
D. King closer
A 13 115/ 2014
[P.T.O.]
98
The type of bond in which every course contains both headers and stretchers, is called :
Answer
A. Flemish bond
99
The vertical side member of a shutter frame is known as ;
Answer
A. Style
100
Length of one link of a metric chain is :
Answer
D. 20cm
-o0o-
1415/2014 | 14 A
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.