| Post Name | DRAFTSMAN GRADE II- FACTORIES AND BOILERS |
|---|---|
| Question Paper Code | 068/2017 |
| Medium of Question | English QUESTION Date of |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
Who expressed the view that the constitution of India “is workable, it is flexible and it is strong enough to hold the country together both in peace time and in war time” ?
Answer
A. Dr.B.R. Ambedkar
2
Who among the following was not a member of The States Reorganization Commission set up in 1953 ?
Answer
D. Pattabhi Sitaramayya
3
The Lok Sabha passed The Rights of Persons with Disabilities Bill-2016 on
Answer
B. 16 December, 2016
4
The 44th Chief Justice of India is
Answer
C. J.S. Khehar
5
The Sadhu Jana Paripalana Yogam was founded in
Answer
D. 1907
6
The first All Kerala Political Conference was held in 1921 at
Answer
A. Ottappalam
7
Sahodara Sangham was founded in 1917 by
Answer
B. K. Ayyappan
8
The editor of the newspaper Mitavadi was
Answer
C. C. Krishnan
9
In which case the Supreme Court of India opined that the Preamble of the Indian Constitution is not a part of the Constitution ?
Answer
B. Berubari Union Case
10
Who was selected as the “Person of the Year 2016” by the Time Magazine ?
Answer
A. Donald Trump
11
Who described the ‘Preamble of the Indian Constitution’ as the ‘Key-note’ ?
Answer
D. Ernest Barker
12
Who criticised the ‘Objective Resolution’ moved by Jawaharlal Nehru in the Constituent Assembly as “wrong, illegal, premature, disastrous and dangerous” ?
Answer
C. M.R. Jayakar
13
The present Speaker of the Bangladesh Parliament is
Answer
C. Dr. Shirin Sharmin Chaudhury
14
The second Ezhava Memorial was submitted to
Answer
A. Lord Curzon
15
The Secretary General of UNO is
Answer
B. Antonio Guterres
16
The Supreme Court of India issued for the first time a contempt of court notice against the sitting judge, Justice C.S. Karnan who is presently serving in
Answer
Question Cancelled
17
The organization called the Samyukta Rashtriya Samiti was formed in connection with
Answer
B. Abstention Movement
18
Samatava Samajam was established in
Answer
A. 1836
19
The present Director General of the World Trade Organization is
Answer
C. Roberto Azevedo
20
The 20th Chief Election Commissioner of India is
Answer
D. Dr. Nasim Zaidi
21
The term modular ratio of the two materials is ratio of __________
Answer
C. their modulus of elasticities
22
A bolt is made to pass through a tube, both ends of them are tightly fitted with the help of washer and nuts. If the nut is tightened
Answer
A. Bolt is under tension and tube is under compression
23
When a force is acting on a body through axially, the strain developed in the perpendicular direction of the force is known as
Answer
B. Lateral strain
24
A cantilever beam is loaded with point load at free end, the bending moment at the free end is
Answer
A. Zero
25
The shape of bending moment diagram for a simply supported beam loaded in its center is
Answer
D. An isosceles triangle
26
The purpose of springs in brakes and clutches are
Answer
Question Cancelled
27
The object of caulking in a riveted joint is to make the joint
Answer
C. Leak proof
28
A column that fails due to direct stress only is called
Answer
A. Short column
29
Lame’s theory is associated with
Answer
B. Thick cylindrical shells
30
The value of compressive strength of a brittle material is ___________ its tensile strength
Answer
B. greater than
31
The variation in the volume of a liquid with variation of pressure is called its
Answer
B. Compressibility
32
A Pitot tube is used to measure the
Answer
A. velocity of flow at the required point in a pipe
33
Coefficient of contraction is the ratio of
Answer
D. Area of jet at vena cotracta to the area of orifice
34
An orifice is said to be large if
Answer
D. The available head of liquid is less than five times the diameter of orifice 6 A
35
An opening in the side of a tank or vessel such that the liquid surface with the tank is below the top edge of the opening is called
Answer
B. Notch
36
Reynolds number is the ratio of the inertia force to the
Answer
B. Viscous force
37
Which of the following pumps is suitable for small discharge and high heads ?
Answer
D. Reciprocating pump
38
Which of the following hydraulic units works on the principle of Pascal’s law ?
Answer
D. Hydraulic press
39
A hydraulic ram is a device used to
Answer
C. To lift small quantity of water to greater height
40
The amount of heat required to raise the temperature of __________ water through one degree is called Kilo Joule
Answer
D. 1000 gram
41
The sum of internal energy and the product of pressure and volume is known as
Answer
C. Enthalpy
42
The heat energy stored in the gas and used for raising the temperature of the gas is known as
Answer
B. Internal energy
43
The hyper bolic process is governed by
Answer
A. Boyle’s Law
44
The compression ratio is the ratio of
Answer
D. Total volume to Clearance volume
45
The compression ratio for petrol engine is
Answer
B. 5 to 8
46
A thermodynamic cycle consisting of, one constant pressure, one constant volume and two isentropic process is known as
Answer
D. Diesel Cycle
47
The calorific volume of gaseous fuel is expressed in
Answer
Question Cancelled
48
The thermodynamic property like temperature is measured on basis of
Answer
A. Zeroth law of thermodynamics
49
Which of the following is a water tube boiler ?
Answer
B. Babcock and Wilcox boiler
50
An economizer is installed in a boiler primarily to
Answer
B. Reduce the fuel consumption
51
The actual power generated in the engine cylinder is called
Answer
B. Indicated power
52
The energy conversion takes place in steam nozzle is
Answer
A. Heat energy of steam into Kinetic energy
53
The thermodynamic cycle on which the petrol engine works
Answer
C. Otto Cycle
54
The air-fuel ratio of the petrol engine is controlled by
Answer
D. Carburettor
55
The unit of thermal diffusivity is
Answer
C. m2/h
56
The automobile radiator is a heat exchanger of
Answer
C. Cross flow type
57
Bell-Coleman cycle is a
Answer
A. Reversed Joule cycle
58
The lead screw of a lathe with nut form a __________ pair
Answer
C. Screw pair
59
V-belts are usually used for
Answer
B. Short drives
60
The ratio of the number of teeth to pitch circle diameter in millimeter is called
Answer
C. Diametrical pitch
61
Which of the following is the function of a washer ?
Answer
C. Provide bearing area
62
A bolt is designed on the basis of __________ with a large factor of safety
Answer
A. Direct tensile stress
63
The size of a gear is usually specified by
Answer
D. Pitch circle diameter
64
The fuel used in a blast furnace is
Answer
B. Coke
65
The machinability of steel is improved by adding
Answer
D. Sulphur, Lead and Phosphorus
66
Age hardening is related to
Answer
A. Duralumin
67
Monel metal is an alloy of
Answer
C. Nickel and Copper
68
A mortise gauge is a
Answer
D. Marking tool
69
Riddle is used for
Answer
B. Cleaning the moulding sand
70
The fullers are used
Answer
B. For necking down a piece of work
71
The operation of cutting a sheet of metal in a straight line along a length is known as
Answer
C. Slitting
72
Acetylene gas is stored in the cylinder in
Answer
C. Liquid form
73
A neutral flame is obtained by supplying
Answer
A. Equal volume of oxygen and acetylene
74
Galvanizing is the process of
Answer
D. Making thin zinc coating by hot dipping
75
The cross-section of a chisel is usually
Answer
D. Octagonal
76
A hacksaw blade is specified by its
Answer
Question Cancelled
77
The type of file used for a wood work is
Answer
C. Rasp cut file
78
The instrument which has all the features of try-square, bevel protractor, ruler and scriber is
Answer
B. Combination set
79
A ring gauge is used to
Answer
A. Check the diameter of shaft or studs
80
The temperature at which the new grains are formed in the metal is called
Answer
D. Re-crystallization temperature
81
Discontinuous chips are formed during machining of
Answer
A. Brittle metals
82
In a centre lathe, the cutting tool is fed in __________ with reference to the lathe axis
Answer
C. Both cross and longitudinal direction
83
The chamfering is an operation of
Answer
D. Beveling the extreme end of a work piece
84
In drilling operation, the metal is removed by
Answer
C. Shearing and extrusion
85
The grinding operation is a
Answer
B. Surface finishing operation
86
A process of removing metal by pushing or pulling a cutting tool is called
Answer
D. Broaching
87
In ultrasonic machining, the metal is removed by
Answer
A. Using abrasive slurry between the tool and work
88
Chemical milling operation is performed
Answer
B. In a tank containing an etching solution
89
PERT stands for
Answer
C. Programme Evaluation and Review Technique
90
Work study is mainly aimed at
Answer
Question Cancelled
91
Which of the following wage incentive plan is applied to all workers ?
Answer
B. Halsey plan
92
Production cost refers to sum of Factory cost and ___________
Answer
A. Administrative overheads
93
Military organization is known as
Answer
A. Line organization
94
Gantt chart is used for
Answer
C. Production schedule
95
In value engineering, imported consideration is given to
Answer
A. Cost reduction
96
Simplex method is the method used for
Answer
C. Linear programming
97
The combustion process in diesel engine is a
Answer
B. Constant pressure process
98
The aluminum alloy is used in cylinder blocks because
Answer
A. It is lighter and have good heat dissipation characteristics
99
The connecting rod is attached to the piston by the
Answer
C. Piston pin
100
In a diesel engine, the function of a fuel injector is to
Answer
D. Spray atomized fuel in the cylinder
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.