| Post Name | DRAFTSMAN GRADE II/ TOWN PLANNING SURVEYOR GR II - Local Self |
|---|---|
| Question Paper Code | 003/2025 |
| Category Code | 682/2023 |
| Date of Test | 7 January 2025 |
| Medium of Question | ENGLISH |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
The designation of B2 drawing board is
Answer
A. 700 × 500 × 15 mm
2
Which part of a T-square is placed adjoining the working edge of the board and is
made to slide ?
Answer
D. Stock
3
The title block of a drawing is drawn at the _____________ of the drawing sheet.
Answer
B. Right bottom
4
Which line connect a note with the feature in an engineering drawing ?
Answer
C. leader line
5
In which type of drawings the lower case letters are usually used ?
Answer
C. Architectural drawings
6
What is the width of arrowhead in a dimension line compared to its length ?
Answer
A. 1/3 of length
7
Which scale is used to represent the same RF but graduated to read different units ?
Answer
B. Comparative scale
8
In first angle projection the right side view is placed at the ______________side of
drawing.
Answer
D. left side
9
In addition to the doors and windows, ventilators should be provided having a total
area of _________ of the floor area.
Answer
A. 4%
10
Which estimate is prepared when further development is required for the progress
of a work ?
Answer
B. Supplementary estimate
11
The hospital buildings are belong to which group of classification ?
Answer
A. Group C
12
For residential buildings the livable area should be _________ of the plinth area.
Answer
D. 50 – 65%
13
The scrap value of a building may be about _________ of its total cost of
construction.
Answer
C. 10%
14
The cost of charge when the engineering department takes up the work of other
department is called as
Answer
C. Centage charges
15
The approximate quantity of work for brick work in cement mortar in foundation and
plinth by an average artisan per day is
Answer
B. 1.25 cu m
16
Which of the following is included in the plinth area of a building ?
Answer
D. Bathrooms
17
The vertical circulation area of a building may be __________ of the plinth area.
Answer
A. 4 – 5%
18
Net annual letting value of a property obtained after deducting the amount of yearly
repairs from gross income is called
Answer
D. Rateable value
19
For fire resistant construction the minimum thickness of timber door leaf should be
Answer
B. 4 cm
20
Which of the following area is included in the carpet area of a building ?
Answer
C. dining
21
Which of the following is the property of material to absorb water vapour from air ?
Answer
C. Hygroscopicity
22
Which of the following is/are the incorrect statement about stones ?
i. The dressing of stones proves to be tedious.
ii. The stones of desired strength and Quality are easily available at moderate rate.
iii. The alternatives to stones namely R.C.C. and steel have proved to be stronger.
iv. The dressing of stones proves to be time consuming.
Answer
C. Only ii
23
A good brick should not break when made to fall on another brick from a height of
________ m.
Answer
Question Cancelled
24
The property of lime by which it sets in thick masonry walls where there is no free
circulation of air is termed as
Answer
B. Hydraulicity
25
Which of the following statement indicate the advantages of timber ?
i. It does not require skilled supervision.
ii. This method of seasoning is cheap and simple.
iii. By this seasoning the moisture content of wood can be brought down to about 10 – 20%.
iv. The process of seasoning is very slow.
Answer
Question Cancelled
26
Which of the following statement indicates the characteristics of good sand ?
i. It should be strong and durable.
ii. It should be chemically inert.
iii. The grains should retain in 4.75 mm sieve.
iv. The grains should pass through IS sieve 75 micron.
Answer
B. Only i and ii
27
Cement mortar recommended for reinforced brick work is
Answer
D. 1 : 3
28
Bessemer pig is obtained from _________ ores.
Answer
B. Haematite
29
Which of the following statement is correct about Aluminium ?
i. It is very soft.
ii. It is a non-magnetic substance.
iii. Its specific gravity is about 2.70.
iv. It readily dissolves in hydrochloric acid.
Answer
D. All of the above (i, ii, iii and iv)
30
The process of slow and homogeneous cooling of glass articles is known as the
Answer
A. Annealing
31
The most common material used as vehicle of a paint is
Answer
C. linseed oil
32
Which is the slump of concrete used for road construction ?
Answer
B. 20 to 40 mm
33
depression or recess made inside the door frame, to receive the door shutter is
known as
Answer
D. Rebate
34
A pier is made monolithic with the walls to increase the stability of wall is called
Answer
A. Buttress
35
How to rectify if settlement of existing foundation has taken place ?
Answer
B. Underpinning
36
Which piles are driven up to a hard stratum in the ground to act as pillars for super
structure ?
Answer
A. Bearing pile
37
Cutting a brick longitudinally in two equal parts is known as
Answer
B. Queen closer
38
Inclined support provided to an unsafe existing structure externally is called
Answer
A. Racking shore
39
Vertical member of a frame, which is employed to subdivide a window or a door
opening is called
Answer
B. mullion
40
Which window is provided near the top of main roof ?
Answer
C. Clere-storey Window
41
Horizontal distance between faces of two consecutive risers is called
Answer
D. Going
42
What is the weight/m of 12 mm diameter round bar ?
Answer
C. 0.89 kg/m
43
The distance between the centres of the rivets in adjacent rows of zig-zag riveted
joint is known as
Answer
C. diagonal pitch
44
What is the excess length of the one side of the cranked bar ?
Answer
B. 0.414 d
45
The triangular upper part of a wall formed at the end of a pitched roof is called
Answer
A. Gable
46
Inner curve of an arch is called
Answer
C. Intrados
47
Which arch is constructed with two curves meeting at the apex of a triangle ?
Answer
B. Pointed arch
48
The vertical joints separating the bricks in either length or cross direction is known
as
Answer
D. Perpends
49
Which bond the bricks are laid at 45° from the centre in both the direction ?
Answer
D. Herring bone bond
50
Which test is carried out for determining workability of concrete ?
Answer
A. Slump test
51
Spread footing for a wall is known as
Answer
A. Strip footing
52
Name the method of damp proofing water proofing compounds or materials are
added during the process of mixing the materials.
Answer
B. Integral treatment
53
In a surveying telescope, cross hairs are fixed in
Answer
Question Cancelled
54
When the angular and linear measurements are equally precise in traversing, the
balancing of the traverse is done by
Answer
C. Bowditch’s rule
55
In levelling, the correction for refraction (in meter) is equal to
Answer
C. 0.0112d2
56
When the whole circle bearing of two lines AB and AC are 65° and 170° respectively.
Then the included angle BAC will be
Answer
A. 105°
57
A series of closed contour line on the map represents a _________ if the higher
values are inside.
Answer
C. Hill
58
The instrument which is the combination of electronic theodolite and electronic
distance meter is
Answer
D. Total station
59
The principle of chain surveying is
Answer
C. Triangulation
60
The error in measured length due to incorrect holding of the chain is
Answer
B. Compensating error
61
The area enclosed in a contour may be found by
Answer
A. Planimeter
62
length of long chord is
Answer
D. 2 R Sin φ/2
63
The back sight reading on a benchmark of reduced level 100.00 is 2.350. If fore sight
reading on the point is 1.520, the reduced level of the point is
Answer
A. 100.830
64
Remote sensing technique are being usefully employed for the purpose of
Answer
D. All of these
65
Which method is used for plotting inaccessible objects, broken boundaries,
rivers etc. ?
Answer
D. Intersection method
66
The magnetic bearing of the line is 50°10′ and magnetic declination is 1°20′ east.
The true bearing of the line will be
Answer
A. 51°30′
67
The irrigation engineering may be defined as
i. The process of artificial supplying water to soil for raising crops.
ii. The science of planning and designing an efficient and economic system.
iii. The capillary water is utilised by the plants.
Answer
Question Cancelled
68
What is the main advantage of irrigation ?
Answer
B. yield of crops
69
A groyne
i. Trains the flow along a certain course.
ii. Perpendicular to bank.
iii. It constructed to protected the river banks.
Answer
C. All (i, ii and iii)
70
Which cross drainage work is constructed to cross the canal and drainage at the same
level ?
Answer
D. level crossing
71
Which element of hydroelectric power plant reduce the water hammer pressure formed
in the penstock ?
Answer
B. Surge tank
72
Which of the following statements is wrong ?
i. Seepage drain reduce the chances of water logging.
ii. The gravity water is harmful to the crops.
iii. Water logging makes the land more productive.
Answer
C. Only (ii and iii)
73
What is the name of the steel placed end to end to provide a level surface for the
movement of trains ?
Answer
C. Rails
74
What is the slope provided to transvers direction road ?
i. Cross fall
ii. Camber
iii. Crown
Answer
A. Only (i and ii)
75
Which shape of the surface drain is most preferred for heavy discharge in road ?
Answer
A. Rectangular
76
What is the minimum width of shoulders provided in national highways ?
Answer
C. 2 m
77
Which of the following statement is wrong ?
i. Bearing plates are used in the case of hard sleepers.
ii. Sleeper holds the gauge at proper rail.
iii. Spacing of sleepers near the rail joint is closer.
Answer
A. Only (i and ii)
78
Which bridge is mostly used for railway bridges of small spans ?
Answer
A. Steel girder
79
How a simple circular curve designated ?
Answer
B. Radius of the curve
80
Which is used for joining the rail ?
Answer
C. Fish plates
81
What is the dimensional formula for strain ?
Answer
B. m0l0T0
82
See saw is a __________ class lever.
Answer
A. First
83
Following are the basic types of stress except
Answer
D. Volumetric stress
84
The length of a rectangle is 1 cm more than its width and its perimeter is 14 cm, then
the area of the rectangle is
Answer
B. 12 cm2
85
The slope of the stress-strain curve in the elastic deformation region is
Answer
A. Elastic modulus
86
An electric pole of 20 m height has casted a shadow of length 20 3 m, on the ground,
then the angle of elevation of the sun at that time is
Answer
C. 30°
87
Activated carbon is used for
Answer
C. Removing odours
88
Which of the following water treatment process is done after filtration of water ?
Answer
D. disinfection
89
Which of the following indicates that the water body has been used for waste
disposal ?
Answer
Question Cancelled
90
When a sewer line dips below the hydraulic grade line the sewer appurtenance
chosen is
Answer
Question Cancelled
91
The sewage treatment units in which anaerobic decomposition of organic matter is
used, are called
Answer
A. Imhoff tank
92
Which of the following is the product obtained when a coagulant is mixed with waste
water ?
Answer
A. Floc
93
The basic software loaded from ROm chip is
Answer
A. BIOS
94
For replacing text from the file, short cut command is
Answer
Question Cancelled
95
Which is the short cut keyboard command of quick calculation Auto CAd ?
Answer
D. Ctrl + 8
96
_________ is the function key used to turn object Snap Toggle in ‘3d’.
Answer
B. F4
97
In which bar do you find the Ortho and Osnap icons ?
Answer
C. Status bar
98
Which command is used to make the curves in the corner of the object ?
Answer
Question Cancelled
99
To Align object with other objects in 2d and 3d in Auto CAd, the command is
Answer
C. AlIGN
100
Which option is used to print all objects with in the printable area of the paper ?
Answer
Question Cancelled
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.