| Post Name | Junior Instructor (Draughtsman - Civil) (SR for SC/ST) - Industrial Training |
|---|---|
| Question Paper Code | 016/2024 |
| Category Code | 507/2022 |
| Date of Test | 30 January 2024 |
| Medium of Question | ENGLISH |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
The test preformed to know the presence of alkaline substances in the bricks is :
Answer
A. Efflorescence test
2
Which of the following is an example of igneous rock?
Answer
B. Granite
3
Crushing strength of a good building stone should not be less than :
Answer
B. 100 N/mm2
4
Cube size recommended for testing the compressive strength of cement as per IS 4031
part 6 :
Answer
D. 70.6 mm
5
Which attachment should be placed on the vicat’s apparatus to find the initial setting time?
Answer
A. Square needle
6
Which of the following is not a defect in timber due to natural forces?
Answer
C. Bow
7
Which one of the following is used as driers in Paint?
Answer
D. Litharge
8
What property of freshly mixed mortar determines its ease of placement, compaction and
finishing?
Answer
A. Workability
9
What is gauged cement mortar?
Answer
C. A mixture of cement, sand, lime and water
10
Which one of the following is an example for mineral admixture?
Answer
A. Fly ash
11
What does the term “batching” refer to in concrete production?
Answer
C. Measurement of materials for concrete
12
The main constituent of Varnish is :
Answer
A. Resin
13
The percentage of carbon content in steel is :
Answer
C. 0.15 to 1.5%
14
Terracotta is a type of :
Answer
B. Earthenware
15
The plastics are :
Answer
D. Insulators
16
If stretchers are seen on the front face of a course in English bond with a wall thickness of 1.5
brick, which one is seen on the back face?
Answer
A. Headers
17
Which of the following is a brick whose width is half the width of a full brick?
Answer
B. Queen closer
18
What is the term for the lower half of the arch between the crown and skewback?
Answer
D. Haunch
19
Which pile passes through the soft soil and rest on the hard stratum at the bottom?
Answer
A. Bearing pile
20
Which part of the well foundation act as an extension of cutting edge and transfers the load
to the soil below?
Answer
B. Curb
21
Which method provides temporary support to maintain stability of the unsafe structure?
Answer
D. Shoring
22
What is the purpose of asphalt tanking treatment in buildings?
Answer
C. Damp proofing
23
What is the process of joining the two pieces of timber at an angle?
Answer
A. Mitring
24
Which of the following is a process of planning off the flat edges or corners of a timber piece
to form an angle of 45 degree?
Answer
C. Chamfering
25
Which of the following is a vertical member employed to subdivide a window or a door
opening vertically?
Answer
D. Mullion
26
Which term refers to the horizontal bottom member of the door/window frame?
Answer
B. Sill
27
In the designation 10 DS 20, letters S stands for :
Answer
C. Single shutter
28
What kind of window has shutters hinged on the sides as in a door?
Answer
D. Casement window
29
Which term refers to the lowest edge of the sloping surface of a roof?
Answer
B. Eves
30
Which type of roof has a pair of common rafters sloping upward from opposite walls meet on
ridge piece at the upper end?
Answer
A. Couple roof
31
The ratio of effective length to least radius of gyration of a compression member is known as :
Answer
B. Slenderness ratio
32
In ISMB 400
Answer
C. Total depth in mm
33
A tension member in which a reversal of direct stress occurs due to loads other than wind or
seismic forces the maximum effective slenderness ratio is :
Answer
C. 180
34
A plate used for connecting two or more structural member interesting each other is called :
Answer
C. Gusset plate
35
The heaviest I section for the same depth is :
Answer
B. ISHB
36
According to IS 456 : 2000 the maximum strain in concrete at the extreme compression
fiber is :
Answer
A. 0.0035
37
According to IS 875 part 3, the factor k2 for the calculation of wind load depends upon :
Answer
D. All of the above
38
Which of the following sections should preferably be used at places where torsion occurs?
Answer
B. Box type section
39
Short term deflection shall be calculated using :
Answer
B. Elastic theory
40
The minimum percentage of reinforcement of the gross sectional area for mild steel and
HYSD bars in slab is :
Answer
C. 0.15% and 0.12%
41
Waste water from bathrooms, kitchen and sink is called as :
Answer
C. Sullage
42
Sewer used to carry waste water from a house to next immediate point of disposal is called :
Answer
C. House sewer
43
Sewer pipes should be designed and checked for :
Answer
D. Both
44
With increase in the temperature of waste water :
Answer
A. DO depletes and bacteriological activity increase
45
Ratio of 5 day BOD to ultimate BOO is :
Answer
A. 2/3
46
Name the head quarter of Western railway :
Answer
D. Church Gate Mumbai
47
CRIS under ministry of railway stands for :
Answer
B. Centre for Railway Information System
48
Coning of wheel is provided for :
Answer
D. All of the above
49
If the sleeper density is N+7 for 13 meter rails, the minimum depth of ballast under wooden
sleepers (25 cm × 13 cm) is?
Answer
B. 20 cm
50
The gradient on which an additional engine is required to negotiate the gradient is called :
Answer
C. Pusher gradient
51
If the ruling gradient is 1 in 20. What is the compensated gradient for a radius of 120 m?
Answer
C. 4.375
52
For a comfortable travel on highways, the centrifugal ratio should not exceed :
Answer
B. 0.22
53
Grade compensation on a horizontal curve on highway is not necessary when :
Answer
C. Gradient is flatter than 4 %
54
The maximum scour depth for the condition of flow at noses of piers, when d is the depth of
scouring is :
Answer
D. 2.00 d
55
The permissible stresses for HYSD bars (Fe 415) for the purpose of designing Bridge Deck as
per IRC 21: 2000 is :
Answer
A. 200 MPa
56
A room to be planned for one function can be used for another function when the principle of
–––––––––––– is considered in the planning process :
Answer
C. Flexibility
57
–––––––––––– specifies the size and layout of drawing sheets :
Answer
B. IS: 10711
58
The standard line thickness required for the border lines of a drawing is :
Answer
C. 0.6 mm
59
Centrodial Lines in Engineering Drawing are indicated by :
Answer
C. Chain Thin Double Dashed Lines
60
Recommended size for letters of the Title of drawing is :
Answer
C. 6 mm
61
The scale used to construct angles in the absence of a protractor is :
Answer
A. Scale of Chords
62
In –––––––––––– Projection, the projectors from an object are parallel to each other and
perpendicular to the plane of the picture :
Answer
A. Isometric
63
A non residential enclosure constructed of non load bearing partitions is called :
Answer
B. Cabin
64
The function key to toggle between GRID ‘ON’ and ‘OFF’ in AutoCAD is :
Answer
D. F7
65
The command for Construction line in AutoCAD is :
Answer
C. XLINE
66
The quantity of honeycomb brick wall is measured in :
Answer
A. sq.m
67
_________ is a type of rough cost estimate :
Answer
A. Abstract Estimate
68
In the analysis of rates, labour is taken on a daily wage basis for _________ hours of working
per day :
Answer
B. 8 hours
69
In computing quantity for painting both faces of a Venetian Door, _________ times the surface
area of one side may be taken as the measurement for both sides :
Answer
D. 3
70
Cornice is measured in _________ with the type and projection specified :
Answer
A. m
71
_________ survey is conducted before setting out of the work on the ground :
Answer
C. Location
72
_________ method of Plane Table Surveying is more suitable for hilly areas :
Answer
C. Intersection
73
A line lying on the surface of the ground with uniform inclination to the horizontal at all
points on it is called :
Answer
B. Contour Gradient
74
The method of levelling done by the measurement of boiling points at different points is :
Answer
C. Hypsometric Levelling
75
The variations in declination due to magnetic storms may be categorised as _________
variation :
Answer
D. Irregular
76
Which of the following results in decrease of chain length?
Answer
B. Sticking of mud
77
Each metric chain shall be accompanied with _________ number of arrows :
Answer
B. 10
78
The datum considered for GTS Benchmark is the mean sea level at :
Answer
A. Mumbai
79
Which of the following lines passes through the centre of the earth?
Answer
C. Plumb line
80
In a Prismatic Compass, graduations are marked on the ring with _________ at the north end
of the needle :
Answer
A. 180°
81
The delta for a crop when its duty is 1728 hectares/cumec on the field and the base period of
this crop is 150 days will be :
Answer
A. 75 cm
82
The first watering which is given to a crop, when the crop is a few centimetres high, is
called :
Answer
B. Kor-watering
83
A canal which is aligned parallel to the natural drainage flow and usually avoids
construction of cross drainage structures is :
Answer
C. Side slope canal
84
The river training works which force the river into a restricted channel, and thus, ensuring a
smooth and an almost axial flow near the weir site are called :
Answer
B. Guide banks
85
The maximum elevation to which the reservoir water surface will rise during normal
operating conditions is called :
Answer
D. Maximum Conservation Level
86
In a hydro-electric scheme, the water coming from the outlet of a reaction turbine is
connected to the tailrace via :
Answer
D. Draft tube
87
Which of the following statements are true regarding a canal syphon?
(i) The drain is taken over the canal
(ii) The FSL of the canal is well below the bottom of drain trough
(iii) The canal flows under syphonic action under the trough
Answer
C. Only (i) and (iii)
88
Which among the following is a Kharif crop?
Answer
C. Maize
89
Which among the following is/are the functions of the Canal Head Regulator :
(i) It regulates the supply of water entering the canal
(ii) It controls the entry of silt in the canal
(iii) It prevents the river floods from entering the canal
Answer
D. All (i), (ii) and (iii)
90
The type of cross-drainage work in which canal water and drain water are allowed to
intermingle with each other is :
Answer
B. Level crossing
91
The frictional resistance experienced by a body while moving is known as :
Answer
C. Dynamic friction
92
According to Lami’s theorem, the correct relation between the forces shown in the figure
given below is :
P Q R P Q R
Answer
B. = =
sin β sin γ sin α sin α sin β sin γ
P Q R
93
The resultant of two equal forces of magnitude P is equal to 3P . Then the angle between
the two forces is :
Answer
C. 60°
94
The theorem stated as “The algebraic sum of moments of a system of coplanar forces about a
moment centre is equal to the moment of their resultant force about the same moment
centre.” is :
Answer
A. Varignon’s theorem
95
The distance of centroid of a semi-circle of radius ‘R’, from its base is :
2R 16R
Answer
C. Bn
96
The moment of inertia of a triangle with base ‘b’ and height ‘h’ about its base is given by the
formula :
bh3 bh3
Answer
A. —
97
The property of a material whereby it absorbs energy due to straining actions by undergoing
plastic deformation is known as :
Answer
B. Toughness
98
The stress at which a material under tension finally fails is called :
Answer
D. Breaking point
99
A Surveyor’s steel tape 30 m long has a cross-section of 15 mm × 0.75 mm. If the force applied
during measurement is 120 N more than the force applied at the time of calibration, what
will be the error in measured length of a line?
Answer
A. 1.6 mm
100
1 MPa = :
Answer
C. 1 N/mm2
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.