| Post Name | Moulder - Kerala State Water Transport Department |
|---|---|
| Question Paper Code | 018/2024/OL |
| Category Code | 094/2023 |
| Date of Test | 29 February 2024 |
| Exam Type | Online Examination |
| Total Questions | 100 |
1
PPE 5 stands for
Answer
C. Eyes and face protection
2
ABC stands for
Answer
B. Airway, Breathing, Circulation
3
Class C ο¬re is used for
Answer
C. Gas and liquid gas
4
The fuel used in a blacksmiths hearth for hand forging is
Answer
B. Charcoal
5
The function of fuel in forging is
Answer
B. To obtain certain heat
6
The anvil is made out of
Answer
C. Cast steel
7
The anvil is used for
Answer
A. To support the job
8
The beak of anvil used for
Answer
B. Bending to round shape
9
Swage blocks are made out of
Answer
B. Cast iron
10
The usage of grooves and slots provided on the swage block
Answer
B. To shape the job
11
Tongs are used for
Answer
A. To hold the job
12
Flat tongs are used
Answer
B. Rectangular jobs
13
The speciο¬cation of hammer is
Answer
B. Weight and shape of peen
14
The weight of hammer is stamped on
Answer
C. Cheek
15
The slight convexity is given to the cutting edge of the chisel is
Answer
C. Prevent digging of the ends
16
The clearance angle of a chisel is the angle between
Answer
A. The working surface and the bottom surface of the cutting edge
17
The pitch of the wave set blade is
Answer
B. 0.8 mm
18
Hacksaw blades are speciο¬ed by
Answer
B. Length, pitch and type of material
19
The angle of centre punch is
Answer
C. 90Β°
20
The angle of dot punch is
Answer
A. 60Β°
21
The tool used to measure length in forging shop is
Answer
B. Brass rule
22
The tool used for transferring and stepping oο¬ distances
Answer
C. Divider
23
Files are classiο¬ed according to their
Answer
B. Length, shape, cut and grade
24
The second cut ο¬le is used for
Answer
B. To give good ο¬nish
25
In double cut ο¬le, the overcut is
Answer
B. 70Β°
26
The ο¬le used in cases where there is a heavy reduction of metal is
Answer
B. Bastard ο¬le
27
The other name of jenny caliper is
Answer
C. Hermaphrodite caliper
28
Bench vice is made of
Answer
D. Cast iron
29
The included angle of VEE in v-blocks is
Answer
C. 90Β°
30
The accuracy of trysquare is
Answer
B. 0.002 mm per 10 mm length
31
"Never lean on the machine" is comes under
Answer
C. Personal safety
32
Which of the statement mentioned is not correct ? 1. Do not give an unconscious person any food or drink 2. Splash water on the face of the unconscious person 3. Do not leave the person alone 4. Do not place a pillow under the head of the unconscious person
Answer
D. 2 only
33
Unguarded machinery is a
Answer
D. Mechanical hazard
34
The three factors of collision causes are 1. Roads 2. Vehicles 3. Pedestrians 4. Drivers
Answer
B. 1, 2 & 4
35
A material which can permanently be extended in all directions, the material is said to be
Answer
B. Malleable
36
Because of the __________ content, cast iron provides an excellent bearing and sliding surface.
Answer
C. Graphite
37
The ultimate tensile strength of wrought iron is about
Answer
D. 350 newton per sq.mm
38
In cartridge brass the percentage of copper and zinc is
Answer
C. 70 : 30
39
Which comes under chemical occupational hazard ?
Answer
D. Corrosive
40
What is the use of strike-oο¬-Bar ?
Answer
A. Remove the excess sand from mould
41
What is the purpose of make denseners by same metal of casting ?
Answer
C. Fuse and become part of casting
42
What is the abbreviation of OSI related to network system ?
Answer
D. Open System Interconnection
43
In admirality gun metal the percentage of Tin is
Answer
A. 10%
44
The solid solution of carbon in gamma iron are called
Answer
B. Austenite
45
Composite materials are classiο¬ed according to
Answer
C. Both
46
When sand is in its natural moist state it is known as
Answer
A. Green sand
47
The heat treatment process which is used to increase the toughness and to reduce brittleness is
Answer
B. Tempering
48
Which of the following cast iron cannot be machined ?
Answer
C. White cast iron
49
The purpose of adding wood ο¬our to moulding sand is to improve
Answer
C. Collapsibility
50
Which of the following is not a defect if permeability is not enough ?
Answer
D. Brittleness
51
The bottom of cupola is made up of which material ?
Answer
A. Cast iron
52
Which is used for general purpose grinding of tough materials ?
Answer
D. Brown aluminium oxide
53
The manufacture has marking on a grinding wheel as 'A36L5V'. The code 'V' represents the
Answer
B. Bond
54
Which is the fuel of cupola furnace ?
Answer
C. Coke
55
Which metal is used for making metal pattern ?
Answer
A. Aluminium
56
Which of the following is the most pattern materials are corrosion prone ?
Answer
D. Grey cast iron
57
A pattern carries which allowance for internal and external surfaces ?
Answer
C. Draft allowance
58
What is the use of core ?
Answer
C. Produce hollow casting
59
What is the colour code of bins for waste paper segregation ?
Answer
D. Blue
60
Which pattern allowance used for ο¬nishing the casting ?
Answer
B. Machining allowance
61
Which material is used for making pattern for mass production ?
Answer
B. Metal
62
Which is made out of the same pouring metal ?
Answer
A. Internal chills
63
Which is used for uniform rate of cooling of a casting ?
Answer
D. Chills
64
What is the advantage of open sand mould ?
Answer
B. No need box
65
Which is used for assemble the split core box ?
Answer
D. Dowel pins and holes
66
Which metal is used for making permanent mould ?
Answer
A. Alloy cast iron
67
Which property of moulding sand is used for make the mould number of times ?
Answer
C. Durability
68
What is the advantage of machine moulding ?
Answer
B. High production rate
69
Which gate is called parting line gate ?
Answer
C. Horse shoe gate
70
Which tool is make the pierced venting in core ?
Answer
A. Sharp wire
71
What is the advantage of stack mould ?
Answer
D. Less boxes
72
Which gating system is used for thin section castings ?
Answer
B. Bench gate
73
What is known as middle box of three box mould ?
Answer
D. Cheek
74
Which is used for withdraw the huge patterns from mould ?
Answer
C. Lifting plate
75
What is the purpose of true centrifugal casting ?
Answer
A. Make hole in casting without core
76
Which material is used for make the mould in continuous casting process ?
Answer
C. Graphite
77
Which property of moulding sand that particles of same attracting each other ?
Answer
C. Cohesiveness
78
Which material is makes for chill ?
Answer
A. Metal
79
Which mould process the entire mould is prepared with the help of manpower ?
Answer
D. Bench mould process
80
What is the reason for using the ο¬ne sand to make the mould ?
Answer
C. For ο¬ne surface
81
Match List I with List II and select the correct answer from the codes given below. List I List II (a) India's fastest ο¬owing river (i) Brahmaputra (b) The red river in India (ii) Gaumukh (c) The site of harappa is located (iii) Teesta on the banks of river (d) The Ganges river originates (iv) Ravi
Answer
C. a β iii, b β i, c β iv, d β ii
82
The idea of 'trusteeship' is associated with
Answer
C. The economic idea of Mahatma Gandhi
83
The ο¬rst district in India without any poor residents as per the latest Multidimensional Poverty Index (MPI) released by the NITI Aayog (2021)
Answer
D. Kottayam
84
Which pairs are incorrect ? a. Atmanuthapam - Kuriakose Elias Chavara b. Nijananda Vilasam - Kumaranasan c. Gajendramoksham Vanchippattu - Sree Narayana Guru d. Lankamardanam - Nitya Chaithanyayathi
Answer
B. b and d
85
There are four main kinds of soil that can be found in Kerala, which among is most fertile ?
Answer
B. Alluvial soil
86
The primary objective of the SGRY Scheme is A) To provide additional and supplementary wage employment and thereby provide food security and improve nutritional levels in all rural areas. B) To provide rural people with the right to document their residential properties so that they can use their property for economic purpose. C) To provide pucca house to all who are houseless and living in dilapidated houses in rural areas.
Answer
A. A only
87
Which of the books is not correctly matched with the Author ? Author Book A. Mahatma Gandhi - Hind Swaraj B. Dadabhai Naoroji - Poverty and Unbritish Rule in India C. Adam Smith - Principles of Economics D. Karl Marx - Das Capital
Answer
C. Adam Smith - Principles of Economics
88
Consider the following statements related to Western Ghats and select the incorrect statement. A. The mountain ranges run parallel to the Bay of Bengal. B. The Anamudi peak is the highest peak in the Western Ghats. C. The Western Ghats also known as the Sahyadri mountain ranges.
Answer
A. Only A is incorrect
89
Which of the following country has hosted the Commonwealth games maximum number of times ?
Answer
D. Australia
90
Match List I with List II and select the correct answer from the codes given below. List I List II (a) Vaikunta Swamikal (1) Atmavidya Sangham (b) Brahmananda Sivayogi (2) Araya Samudaya Sanghatana (c) Pandit K.P. Karuppan (3) Samatva Samajam (d) Vagbhatanandan (4) Anandamahasabha
Answer
D. a β 3, b β 4, c β 2, d β 1
91
Arrange the following in chronological sequence and select the correct answer from the codes given below. 1. The Khilafat Movement 2. The Quit India Movement 3. Swadeshi Movement 4. The Civil Disobedience Movement
Answer
C. 3, 1, 4, 2
92
The highest literary honour is given by the Kerala Sahitya Akademi, Government of Kerala
Answer
B. The Ezhuthachan Puraskaram
93
Identify the Jet stream which is responsible for bringing western disturbances from the Mediterranean region into the Indian subcontinent.
Answer
C. Westerly Jet stream
94
Which of the Movement is correctly matched with the Reformers ? Movements Reformers A. Prardhana Samaj - Atmaram Pandurang B. Satyashodak Samaj - E.V. Ramaswami Naicker C. Self Respect Movement - Jyotiba Phule D. Hitakarini Samaj - Viresalingam
Answer
A. A and D
95
Which among the following statement is associated with KIIFB ? A. A government owned ο¬nancial institution to mobilize fund for infrastructural development. B. A government agency for empowering industrial growth across Kerala. C. To provide investment for projects in the state of Kerala in the sectors of irrigation, road, power, water supply, ports etc. D. If provides support to businesses, export-import facilities etc.
Answer
B. A and C
96
Match Column A with Column B. Column A Column B a. Santhal Rebellion (i) Malabar b. Bhil Uprisings (ii) Ranchi c. Munda Uprisings (iii) Rajmahal hills d. Kurichya Rebellion (iv) Mangad hills
Answer
D. a β iii, b β iv, c β ii, d β i
97
With respect to "Nai Talim" consider the following statements. A. Mahatma Gandhi's perspective of education is known as Nai Talim. B. This system of education recommended free and compulsory education in mother tongue. C. Implemented three language formula. D. Education should be related to some productive occupations. Which of the above are correct ?
Answer
A. A, B and D
98
With reference to the project 'Veda' consider the following statements. A. The Veda SLV is a three stage, solid-propellant rocket. B. 'Veda' means vehicle for Defence Application. C. The Veda vehicle is intended for launching defence satellites into a lower orbit. Choose the correct answer from the codes given.
Answer
D. A, B and C
99
India's ο¬rst Science city
Answer
C. Kolkata
100
Which sports event is known as the "BWF Super Series" ?
Answer
B. Badminton
Discussion
Ask a doubt or share a tip.
No comments yet β start the discussion.