| Post Name | Tracer/ Overseer Gr III(B/T)/ Work Superintendent 189/2023,530/2023 |
|---|---|
| Question Paper Code | 082/2024 |
| Category Code | 189/2023, 530/2023, 713/2023 |
| Date of Test | 10 July 2024 |
| Medium of Question | ENGLISH |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
Which part doesnβt belong to T square ?
i. Working edge
ii. Blade
iii. Battens
iv. Ebony
Answer
D. iii and iv
2
Small bow compass can draw circles less than ________ radius.
Answer
B. 25 mm
3
Which of the following is hardest pencil ?
Answer
B. 9H
4
What is the ratio of length and width of drawing sheet ?
i. 1 : 1.414
ii. 2 : 1
iii. 1 : 2
iv. 1 : 1.5
Answer
Question Cancelled
5
What is the inclination of letters recommended by BIS ?
Answer
Question Cancelled
6
Which of the following line projecting from the feature and extending beyond the
dimension line ?
Answer
A. Extension line
7
Which of the following are reducing scale ?
i. 10 : 1
ii. 10 : 2
iii. 1 : 2
iv. 1 : 5
Answer
C. iii and iv
8
Which one of the following is the sum of the interior angles of polygon where βnβ is
the number of sides ?
Answer
A. (2 Γ n β 4) Γ right angle
9
The conic section at which section plane is inclined to the axis and is parallel to
one of the generators of the cone, the section is called
Answer
A. Parabola
10
In orthographic projection, the projectors are ________ to the plane of projection.
Answer
C. Perpendicular
11
In which type of survey, the shape of the earth is taken into account ?
Answer
B. Geodetic survey
12
The process of fixing intermediate points on a survey line is called
Answer
C. Ranging
13
The direction of a line relative to a given meridian is called
Answer
A. Bearing
14
The process of putting the plane table into some fixed direction so that line representing
a certain direction on the plan is parallel to that direction on the ground
Answer
D. Orientation
15
Which line is normal to the level line at a point ?
Answer
B. Vertical line
16
What is the inclination of the needle with the horizontal in prismatic compass ?
Answer
A. dip
17
Which levelling is adopted while it is not possible to set up the level mid way between
two points as across river or lake ?
Answer
D. Reciprocal levelling
18
The bottom of a RCC chhajja A was taken as a temporary bench mark (Rl 75.150 m).
Reading on inverted staff on bench mark A is 2.760 m and reading on peg B on
ground is 1.435 m. What is reduced level of B ?
Answer
A. 70.955 m
19
In which method of contouring, spot levels are taken along a series of lines laid over
the area ?
Answer
B. Indirect method
20
A reliable instrument used for setting out a grade contour is
Answer
C. Ceylon ghat tracer
21
What is the process of turning the telescope in vertical plane about its horizontal axis
through 180Β° ?
Answer
A. Transiting
22
Which angle is measured clockwise from the previous line to the following line ?
Answer
B. Direct angle
23
Value of contour interval adopted for town planning schemes, reservoirs etc.
Answer
C. 0.5 to 2 m
24
Which is the carrier for distance measurement in almost all total stations ?
Answer
B. Infrared rays
25
What least angle capable of measuring with best quality total station ?
Answer
Question Cancelled
26
What is the maximum safe bearing capacity of black cotton soil in dry condition ?
Answer
Question Cancelled
27
What is the name of tool used for setting angle in brick masonry ?
Answer
A. Bevel
28
Which plaster material used in X-ray rooms to protect the persons working ?
Answer
C. Barium plaster
29
The cracks occur in a centre of a tree and they extend from pith to sapwood in the
direction of medullary rays
Answer
D. Heart shakes
30
What is the name of the term for hard brownish, unglazed vitrified ceramic material
used for architectural ornamentation ?
Answer
B. Terracotta
31
The commonly used retarders are
Answer
B. Gypsum
32
What is the maximum span for double joist floor ?
Answer
D. 7.5 m
33
What is the name of term used for the vertical joints separating the bricks in either
length or cross direction ?
Answer
A. Perpends
34
What is the mass of 6 mm dia. of steel bar ?
Answer
A. 0.222 kg
35
What is the slope usually given on RCC flat roof ?
Answer
Question Cancelled
36
What is the name of the test to determine the durability or weathering quality of
stones ?
Answer
D. Crystallization test
37
Which class of brick is used for unimportant situation and for internal walls ?
Answer
C. 3rd Class brick
38
What is the name suitable for cold weathering concrete ?
Answer
C. Extra rapid hardening cement
39
Name the sand which passes through a sieve with clear opening of 3.17 mm and
used for masonry work.
Answer
B. Coarse sand
40
What is the weight of steel in kg/m2 ?
Answer
B. 7850
41
What will happen when vertical and inclined surface are too thickness painted ?
Answer
A. Sagging
42
What is the name of the treatment that to protect the building against termites is a
maintenance treatment open earth around building and treat with chemicals ?
Answer
C. Post-construction treatment
43
Slate is an example of
Answer
Question Cancelled
44
What is the name of class lime which can be used for structural work such as arches,
domes etc. ?
Answer
A. Class a
45
What is the yield strength of HySd bars ?
Answer
C. 415 N/mm2
46
The decrease or loss in the value of property due to structural deterioration use, wear
and tear is called
Answer
D. depreciation
47
What is the measurement unit for the cornice works in estimation ?
Answer
A. meter
48
The estimate prepared while the original sanctioned estimate is exceeding by more
than 5 percentage is called
Answer
B. Revised estimate
49
Printed list of rates of various items of work maintained by the engineering
department
Answer
A. Schedule of rates
50
Annual periodic payment for repayment of capital amount invested by a party
Answer
B. Annuity
51
Plastering area taken for a pillar
Answer
D. Perimeter Γ height
52
Forest Conservation Act was passed in the year
Answer
B. 1980
53
IS Code used for fire safety is
Answer
A. IS 1641 β 1960
54
Plan approved and sanctioned by the competent authority
Answer
D. Sanctioned plan
55
Permissible F.A.R. for the commercial building
Answer
Question Cancelled
56
The estimated cost charged to meet the expense of establishment designing, planning,
supervision etc. which is of 10 β 15% of the estimated cost
Answer
D. Centage charge
57
Statement of various items of work giving the description of quantities and unit rates
where the amount columns are left blank is called
Answer
A. Bill of quantities
58
diameter of mild steel bars is expressed in
Answer
A. mm
59
Unit of payment for boring holes in iron
Answer
B. Per number
60
Which one is not included in job overhead ?
Answer
A. Establishment
61
Importance of orientation of building
Answer
D. Reduction of energy bills
62
maximum covered area for an industrial building
Answer
Question Cancelled
63
Carpet Area
Answer
C. Total floor area β circulation area
64
Nominal size bricks needed for 1m3 of brick work
Answer
A. 500
65
Process of determining the value of the property or the fair price of property
Answer
A. Valuation
66
In which irrigation method, water is supplied to lower level by the action of gravity ?
Answer
A. Flow
67
What is the relation between duty
Answer
C. β =
68
What is the first watering before sowing the crop ?
Answer
B. Paleo
69
Which is called as safety valve of a dam ?
Answer
C. Spill way
70
What is the classification of dam based on use ?
Answer
A. detention
71
When does hydrograph called as unit hydrograph ?
Answer
A. 1 cm of runoff from rainfall
72
Which is the main function of diversion head work of a canal ?
Answer
D. To raise water level
73
Which is the main factor for selection of site for a reservoir ?
Answer
A. maximum runoff
74
What is the name of the structure placed in river to increase the depth of water ?
Answer
Question Cancelled
75
Which element of hydroelectric power plant reduce the water hammer pressure
formed in the penstock ?
Answer
B. Surge tank
76
Which canal is also known as ridge canal ?
Answer
B. Watershed
77
What is also known as canal fall ?
Answer
B. Canal drop
78
Which cross drainage work is constructed to carry canal below drainage ?
Answer
B. Super passage
79
Which of the following is the cause of the property that allows liquid to resist an
external force ?
Answer
D. Surface tension
80
Barometer is used to measure
Answer
B. Atmospheric pressure
81
Which of the following statements is/are correct about units ?
i. Time is a fundamental unit.
ii. In FPS system of units, unit of length is Foot.
iii. Area is a derived unit.
Answer
C. All of the above (i, ii and iii)
82
2 kilograms is equal to ___________ pounds.
Answer
A. 4.41
83
What is the base of a triangle having an area of 50 cm2 and height 100 mm ?
Answer
B. 10 cm
84
A wire bend in the form of a circle of radius 35 cm was reshaped to a square. Then
what is the length of one side of that square ?
Answer
B. 55 cm
85
How many litres of water can be stored in a water tank having length = 1 metre,
width = 0.5 metre and height = 0.8 metre ?
Answer
D. 400
86
How many spherical balls of radius 1 cm can be made from a sphere of 15 cm
radius ?
Answer
A. 3375
87
Which of the following statements is/are correct about energy ?
i. Energy of a body is its capacity to do work.
ii. Unit of energy is same as the unit of work.
iii. Energy of one form cannot be transformed into energy of another form.
Answer
B. Only ( i and ii)
88
When an external force acts on a material, there is a change in its dimension and
shape. This deformation is called
Answer
D. Strain
89
Which of the following statements is/are correct about friction ?
i. limiting friction is less than rolling friction.
ii. Rolling friction is equal to sliding friction.
iii. Rolling friction is always less than limiting friction.
Answer
C. Only (iii)
90
The rate of change of displacement of a body in motion in a given direction is
called
Answer
A. Velocity
91
What is mechanical advantage of a simple machine ?
Effort load
Answer
B. load Effort
dis tance moved by the effort
92
The positive bending moment in a beam is often called _______ moment.
Answer
C. Sagging
93
Which of the following statements is/are correct about explode command ?
i. Breaks a compound object into its component objects.
ii. When you start explode command, AutoCAd prompt you to select one or more
complex objects.
iii. If objects canβt be exploded, AutoCAd displays how many objects could not be
exploded at command line.
Answer
D. All of the above (i, ii and iii)
94
Which among the following command is used to create a region or a polyline from
an enclosed area ?
Answer
C. BOUNdARy
95
Which of the following statements is/are correct about snap mode ?
i. Restricts cursor movement to specified grid intervals.
ii. Tracks the cursor to increments along polar alignment paths.
iii. Snap mode is toggled using the F7 Key.
Answer
A. Only (i and ii)
96
Which of the following tool is used to connect two objects with an arc with a specified
radius ?
Answer
B. Fillet
97
Which of the following statements is/are correct about ortho mode ?
i. If ortho mode is enabled, you will only be allowed to draw lines along the UCS
axis.
ii. If ortho mode is enabled, you will be able to draw lines at any angle.
iii. To toggle ortho mode on and off, press the F8 key.
Answer
C. Only (i and iii)
98
In AutoCAd, the keyboard shortcut Ctrl + 1 is used to
Answer
C. Show properties palette
99
Which of the following command is used to add or edit plotter configuration ?
Answer
C. PlOTTERmANAGER
100
Which of the following in AutoCAd displays the cursor location, drawing tools and
tools that affect your drawing environment ?
Answer
B. Status Bar
Discussion
Ask a doubt or share a tip.
No comments yet β start the discussion.