| Post Name | TRACER |
|---|---|
| Department | TOWN AND COUNTRY PLANNING |
| Question Paper Code | 167/2015 |
| Date of Test | 10 September 2015 |
| Medium of Question | ENGLISH |
| Exam Type | OMR Examination |
| Total Questions | 75 |
1
The angle between two curved lines is known as
Answer
A. Spherical angle
2
| Which of the following is the classification based upon the system of surveying ?
Answer
B. Triangulation surveying
3
The survey that does not deal with mapping of large water bodies is
Answer
D. Cadastral Survey
4
During the office work, surveyor does
Answer
A. Design of structure
6
The simplest figure which can be plotted without angles but with sides
Answer
D. Triangle
7
The Survey line which fixes up the direction of all other Survey line is
Answer
B. Base line
8
The Instrument which automatically records the number of steps taken placing in a given survey line
Answer
C. Passometer
9
Too long chain may be adjusted by
Answer
A. Closing up the joints
10
One of the duties of leader in chain surveying is
Answer
B. To obey instruction of follower
11
The surveying best suited for dense area and fall of many details is
Answer
D. Compass surveying
12
Part of compass adjusting the prism according to eye height is
Answer
C. Focussed stud
13
Whole circle bearing 176° equal to quadrantal bearing of
Answer
C. S#E
14
The difference between forebearing and backbearing of a survey line should be
Answer
A. 180°
15
In which step of field works, area of plot is divided into polygon or triangle, in compass surveying ?
Answer
B. Reconnaissance of area
16
Which one is, in the following, that does not have the object of levelling ?
Answer
C. Indirect ranging
19
One significance of “Y level’
Answer
D. Not rigid in construction
20
Which of the following, Bench mark is established with high precision ?
Answer
B. G.T.S. Benchmark
21
If higher contours are inside and lower contours are outside, object will be
Answer
A. Hill
22
Which one is one significance of direct methods of contouring ?
Answer
C. Most accurate
23
The need of drawing cross section from a contour map is to calculate
Answer
D. Earth work
24
Contour line cross each other in case of
Answer
B. Overhanging cliff
25
Contour Interval is kept higher when
Answer
A. Money available is limited
26
Which one is not a part of Telescopic alidade ?
Answer
C. Horizontal Circle
27
Systematic operation of temporary adjustment of planetable is
Answer
B. Observation after orientation
28
Magnetic needle method is used in plane table when
Answer
A. Required less accuracy
29
When surveying control from a single station and in smaller area, the method of surveying is
Answer
B. Radiation
30
Merits of plane table Surveying is
Answer
D. Suitable for small scale map
31
When calculating boundary area, total no. of ordinates must be odd in
Answer
D. Simpson's rule
32
Three successive ordinates are 2m, 1m and 2m and interval between ordinates is 10m, Then area enclosed by ordinate by Simpson’s rule in m?
Answer
C. 26.67
33
Aceylon ghat tracer does not consist
Answer
A. Tripod
34
Sextend is used for measuring
Answer
C. Angle
35
The instrument which is having mirror, metal frame and gimbal is
Answer
B. Clinometer
36
A Theodolite whose telescope can be revolved through a complete revolution in vertical plane about it’s horizontal axis, is known as
Answer
D. Transit theodolite
37
Size of theodolite varies from
Answer
A. 10 to 30cm
38
Three screw type theodolite is preferred when
Answer
B. Levelled more quickly
40
Least count of transit theodolite reading
Answer
D. 20 seconds
41
Plumb bob of theodolite is suspended from
Answer
C. hook
42
Axis about which telescope of theodolite can be rotated in horizontal plane is known as
Answer
A. Vertical axis
43
In double Vernier theodolite
Answer
B. Main scales are marked in both directions
44
When focussing object glass, Telescope is
Answer
D. Directed to object
45
Direct angle Obtained from theodolite may be between
Answer
A. 0° and 360°
46
Point of curve is also known as
Answer
C. beginning of curve
48
Compound curve has
Answer
B. Arcs of different radius
49
If tangent, distance 20 m and radius of curve 200 m, when setting out curve, Radial offset from tangent is equal to
Answer
A. 1m
50
Magnitude of Centrifugal force along a curved track, generally is
Answer
B. Inversely Proportional to radius of curvature
51
For the computation of earth work, the data not required is
Answer
C. Top width of cutting
52
Full detailed survey work along the most economical route of road is done by
Answer
D. Location survey os A road has given maximum gradient 1 in 50 minimum gradient 1 in 200. What will be possible exceptional gradient value when designing same road ?
54
General application of ‘chain thin double dash line’ in engineering drawing
Answer
A. Centroidal line
56
The command allowing to set lower left corner and upper right corner of drawing area in autocad is
Answer
D. Limit To draw two rectangles 50x 100 cm and 250 x 350 cms, in autocad, set the snap to
60
A junction means connection between a main wall and a
Answer
D. Partition wall
61
Inclined surface of brick work should be checked by
Answer
C. Wooden template
62
Brick should be saturated with water before making wall so as to prevent absorption of moisture from
Answer
A. Mortar
63
Magnet represents all material which attracts : ?
Answer
D. Iron
64
‘4 cos°a—3 cos a’ is equal to
Answer
A. cos 3a
66
Simplify (sec 6+ tan 0) (1—sin 6)
Answer
C. cos 6
68
An example which is not optical medium in light theory is
Answer
B. Stone
70
The angle between two surfaces at which refraction takes place is called
Answer
D. Angle of prism Was Formula for total surface area of a hemisphere of radius r
73
If major axis 6 cm and minor axis 4 cm, area of ellipse in cm? is
Answer
D. 67
74
If sides of a triangle are 4 cm and 5 cm and angle between them is 30°, Area of triangle is
Answer
C. Sem?
79
Write one factor of the term x*—x—-6
Answer
B. x-3
80
In the quadratic equation 3x*—5x+2=0 discriminant value is equal to
Answer
D. 1
81
Evaluate log;, 1000+log, e
Answer
A. 4
83
Equal chords of circle always subtend equal angle at
Answer
B. centre of circle
85
Length of tangents drawn from an external point to a circle are in the ratio of
Answer
D. 1:1
86
Any rays passing through the centre of curvature of spherical mirror are reflected back. along the
Answer
B. Same path
87
In a concave mirror, position of object is beyond the centre of curvature, position of image will be
Answer
C. Between centre of curvature and focus
88
The material which do not allow light to pass through them at all is called
Answer
B. opaque
89
When a material is subjected to external force, stress is induced
Answer
D. inside the material
91
The bending moment at the free end of a cantilever will always be
Answer
C. Zero
93
6 mm diameter steel bar has approximate weight per metre length
Answer
D. 0.22 kg To construct 1m? of brick masonry, approximate no. of bricks (20 x 10x10 cms size) required
95
To prepare the preliminary estimate for an irrigation channel, the rate is calculated based upon
Answer
C. Area of land commands
96
When constructing In circle of a triangle, the centre of circle will be getting when
Answer
D. bisecting any two angles of triangle
98
Write expression ( x+ =) x = 4in the form of quadratic equation
Answer
B. x2-4x+3=0
99
Area of regular hexagon having side ‘a’
Answer
C. 3v3 2 a
100
If log 0.2521 = —0.5984, Evaluate log 0.02521 approximately
Answer
D. 2.4015 -000- 167 / 2015 14 A
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.