| Post Name | Tracer- Soil Survey and Soil Conservation |
|---|---|
| Question Paper Code | 164/2024 |
| Category Code | 600/2023 |
| Date of Test | 22 November 2024 |
| Medium of Question | ENGLISH |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
In the following solid objects which has 5 triangular faces ?
Answer
B. Pentagonal pyramid
2
The tool used to draw vertical lines by sliding along T-square
Answer
D. Set square
3
The conversion of 600 mm in 1 : 20 scale is related with normal scale is
Answer
B. 3 cm
4
Where is the front elevation placed in first angle projection ?
Answer
A. Above the plan
5
In the given choices which one is a four-sided figure in which all the sides are
equal but not at right angle ?
Answer
C. Rhombus
6
Which of the following statement is not true ?
Answer
C. dimension lines are continuous thick lines
7
The sizes of letters and numerals in drawing for Sub-titles and headings are
Answer
D. 3, 4, 5 and 6
8
The scale which shows only two consecutive units is
Answer
C. Plain scale
9
Which of the following rules related to measurement is false ?
Answer
B. The method of measurement may not be uniform
10
An estimate is preparing from the following data drawing, Rate and
Answer
B. Specification
11
The tolerances in measurements and calculations for weights should be
Answer
D. 0.001 tonne
12
Some changes or additional works due to material deviation of a structural nature
from the originally approved design, a __________ estimate is prepared.
Answer
C. Supplementary estimate
13
___________ is the amount paid every year towards the capital invested by a
party.
Answer
A. Annuity
14
The measurement of brick work should be taken to nearest
Answer
D. 0.01 m
15
Rate analysis of any item depends on labour, cost of material and
Answer
C. sundries
16
The term ________________ is used to designate a procedure of valuing an item
on the basis of the materials and labours used actually.
Answer
D. day work
17
The term _____________ is used to denote the actual amount incurred in
producing a commodity.
Answer
C. cost
18
For painting, areas should be worked out
Answer
Question Cancelled
19
The value of the property after being discarded at the end of utility period, without
broken into pieces is known as
Answer
D. salvage value
20
For measurement of stone work _________ Indian Standard shall be followed.
Answer
Question Cancelled
21
The process of taking out stones from natural rock is known as
Answer
B. Quarrying
22
A tool used to check the verticality of the structure is called
Answer
C. Plumb bob
23
Hydraulicity is the property of lime.
Answer
A. To set and harden even under water
24
The timber piece whose breadth and thickness exceeds 50 mm, but are less than
200 mm in length is called
Answer
B. Scantling
25
Which of the following stress can Plain cement concrete endure ?
Answer
A. Compressive stress
26
Which one of the following mechanical properties enables a metal to be made in
to thin sheets ?
Answer
D. malleability
27
Cast iron is a product of
Answer
B. Cupola
28
Which of the following types of glasses is also known as hard-glass ?
Answer
D. Potash-lime glass
29
The process of coating iron or steel sheets with a thin coat of Zinc to prevent iron
from rusting is called
Answer
B. Galvanisation
30
The most commonly used admixture which prolongs the setting and hardening
time is
Answer
A. Gypsum
31
The horizontal layer of mortar upon which bricks are laid in a brick masonry is
called
Answer
C. Bed joint
32
Sand does not show any bulking when
Answer
D. Completely saturated
33
A brick laid with its length parallel to the face of the wall is called
Answer
B. Stretcher
34
A projecting stone which is usually provided to serve as support for roof truss is
called
Answer
D. Corbel
35
What is the name of member that supports the boards in the centering of arches ?
Answer
B. Props
36
Arch constructed over a wooden joist or flat arch is known as
Answer
C. Relieving arch
37
What is a rafter provided at junction of two slopes ?
Answer
C. Hip rafter
38
Which one is an isolated footing for a column ?
Answer
A. Pad footing
39
The external jamb of a door or a window opening at right angles to the wall face is
known as
Answer
B. Reveal
40
A vertical window built in the sloping side of the pitched roof is
Answer
C. dormer window
41
Tapering step are used to change the direction of flight is
Answer
C. Winder
42
What is the weight per metre length of 6 mm diameter round bar ?
Answer
A. 0.22 kg/m
43
What is the minimum distance between centres of any two adjacent rivet holes to
the nominal diameter of the rivet ?
Answer
D. 2.50 times
44
The bond in which headers and stretchers are laid in alternate course is known as
Answer
B. English bond
45
Removable of probs to slabs spanning up to 4.5 m is
Answer
A. 7 days
46
The type of flooring perfectly noiseless and is used in theatre is named as
Answer
C. Cork floor
47
Compressive strength of 1:2:4 mix 150 mm size concrete cube at 28 days is
expressed in
Answer
B. 15 N/mm2
48
Recommended slump of concrete for road construction is
Answer
A. 20 to 40 mm
49
The diagonal piece of timber used to give rigidity to the framework is known as
Answer
B. Bracing
50
Beam is used for the span is more than 20 m and load is heavy is called
Answer
D. Plate girders
51
Which stone joint is used in structures like sea wall where lateral pressure is more ?
Answer
C. Tabled joint
52
Which is useful for large number of people or vehicles are to be moved from floor
to floor ?
Answer
B. Ramp
53
The most accurate and common method for measuring distance with a chain or
tape is called
Answer
A. Chaining
54
Revenue chain is commonly used for measuring field in
Answer
C. Cadastral survey
55
The size of chain survey field book is
Answer
B. 20 cm × 12 cm
56
The bearing of line in the direction of the progress of survey is called
Answer
D. Forward bearing
57
The horizontal angle which the magnetic meridian makes with the true meridian is
known as
Answer
A. magnetic declination
58
In plane table surveying ____________ method is used for locating the station
points only.
Answer
D. Resection
59
_______________ is a fixed reference point of known elevation.
Answer
A. Bench mark
60
The process of tracing contour lines on the surface of the earth is called
Answer
C. Contouring
61
multiply the length of the line by the Cosine of its reduced bearing gives
Answer
A. latitude
62
___________ are regular bends provided in the lines of communication like roads,
railways etc. to bring about the gradual change of direction.
Answer
D. Curves
63
In a ranging process the surveyor gives a signal to the assistant, ‘both hands
above head and then brought down’ it means
Answer
A. Correct
64
Which instrument is a combination of Edm, electronic theodolite and
micro processor ?
Answer
A. Total Station
65
GPS stands for
Answer
A. Global Positioning System
66
_______________ is used for orienting the plane table to magnetic north.
Answer
D. Compass
67
Which method of irrigation is called trickle irrigation ?
Answer
C. drip
68
What is the name of the impervious barrier constructed across a perennial river to
raise the water level on the upstream side ?
Answer
Question Cancelled
69
What is the total depth of water required by a crop during the entire period in the
field ?
Answer
C. delta
70
Which crops are sown in autumn season and harvested in spring season ?
Answer
C. Rabi
71
What is the name for accumulation of water in the form of an artificial lake ?
Answer
D. Reservoir
72
When does hydrograph called as unit hydrograph ?
Answer
A. 1 cm of runoff from rainfall
73
Where did the Central Road Research Institute started ?
Answer
C. New delhi
74
What is the restriction given to lengthy straight routes while setting road alignment ?
Answer
A. minimum
75
Which alternative road is provided to divert traffic to avoid obstruction ?
Answer
B. loop
76
What is another name of continuous bay method in cement concrete road
construction ?
Answer
B. Strip
77
What is the process for filling the ballast around the sleepers ?
Answer
C. Boxing
78
What is the length of bull-headed rail ?
Answer
B. 18.29 m
79
Which warner signal is first seen by the driver in railway station ?
Answer
C. Outer signal
80
Which foundation is provided for heavy works at a depth of 12 m to 15 m below the
level of standing water surface ?
Answer
B. Caisson
81
The horizontal tunnels constructed at shallow depths along the banks of the river to
intercept the ground water table are called
Answer
D. Infiltration galleries
82
The growth of population may be conveniently represented by
Answer
C. logistic curve
83
For an area developed in haphazard way, the type of layout used for the distribution
of pipe is known as
Answer
A. dead end system
84
For the sewers of diameter less than 600 mm the type of joint preferred is
Answer
B. Spigot and socket joint
85
The privy pit should be located at least _________ from the well or other ground
water supply.
Answer
Question Cancelled
86
The spacing of manholes for pipes having a diameter greater than 2 m is
Answer
C. 300 m
87
The capacity of a strained body for doing work on the removal of the straining force
is called
Answer
A. Resilience
88
When a bar is subjected to a change in temperature and its deformation is prevented
the stress induced in the bar is
Answer
D. Thermal stress
89
The diagonal of a cube is 4√3 cm. Find the surface area of the cube.
Answer
B. 96 cm²
90
A machine having an efficiency greater than 50% is known as
Answer
A. Reversible machine
91
One watt is equal to
Answer
B. 1 joule/s
92
When the spring of a watch is wound, it will possess
Answer
Question Cancelled
93
Which year does first micro processor was invented ?
Answer
B. 1971
94
What is the extension file of note pad ?
Answer
Question Cancelled
95
Choose from the following is not an analytical entity.
Answer
C. Spline
96
The shortcut for mirror command is
Answer
D. mI
97
In which system of drawing in CAd the line can be drawn with distance and angle ?
Answer
B. Polar co-ordinate
98
What is the lowest RAm in which Auto CAd 19 will work ?
Answer
Question Cancelled
99
What is the highest dots per inch
Answer
Question Cancelled
100
What is the use of ‘Q’ shortcut key in Auto CAd ?
Answer
Question Cancelled
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.