| Post Name | TRACER - TOWN AND COUNTRY PLANNING |
|---|---|
| Question Paper Code | 082/2022 |
| Category Code | 649/2021 |
| Date of Test | 24 August 2022 |
| Medium of Question | ENGLISH |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
The following line is used for dimension line
Answer
B. Continuous thin
2
In aligned system of dimensioning the dimension may be read from
Answer
A. Bottom or right hand edges
3
The length : width in case of an arrow head is
Answer
C. 3 : 1
4
The internal angle of regular hexagon is _________ degree.
Answer
C. 120
5
A line of 6 m is shown by 6 cm on a scale, its Representation Factor (RF) is
Answer
Question Cancelled
6
A point p is above Horizontal Plane (HP) and in front of Vertical Plane (VP).
The point is
Answer
A. First quadrant
7
The section cut by a plane on a right circular cone are called as
Answer
B. Conic sections
8
In conics the ___________ is revolving to form two anti parallel cones joined at the
apex.
Answer
C. Generator
9
If a plane is perpendicular to vertical and inclined to horizontal plane with 30 degrees
then the vertical trace makes _____________ of xy reference.
Answer
A. 30 degrees
10
The preferred size of the drawing sheets is recommended by the
Answer
A. BIS
11
The error due to bad ranging is
Answer
A. Cumulative (+ve)
12
The smallest length that can be drawn on a map is
Answer
A. 0.2 mm
13
The difference between the most probable value of a quantity and its observed
value is
Answer
D. Residual error
14
The degree of precision required in survey work mainly depends upon the
Answer
A. Purpose of survey
15
The relative horizontal positions of various points in surveying are determined by
Answer
Question Cancelled
16
Prolongation of a chain line across an obstruction in chain survey is done by
Answer
B. Drawing perpendicular with a chain
17
Geodimeter is based on
Answer
A. Propagation of modulated light waves
18
True bearing of a line is 10 degree and the magnetic declination is 2 degree W its
magnetic bearing is
Answer
Question Cancelled
19
Which of the following reference direction is used in a geodetic survey ?
Answer
A. True
20
LCD in the control panel of a total station stands for
Answer
B. Liquid Crystal Display
21
Laser plummet in total station is used for
Answer
A. Centering
22
A mosque is situated on the far side of a river and is inaccessible it can be located by
Answer
C. Intersection
23
For surveying of broken boundaries with a plane table most appropriate method
will be
Answer
B. Intersection
24
For mountainous region, a suitable contour interval may be
Answer
Question Cancelled
25
Removal of parallax may be achieved by
Answer
C. Refocusing the eyepiece and the objective
26
A polar array creates new objects
Answer
C. In a circular pattern
27
How many point do you need to define for rectangle command ?
Answer
B. Two
28
Which command creates a new object parallel to the object ?
Answer
C. Offset
29
Which command converts discrete object in polyline ?
Answer
A. Join
30
Maximum length of a construction line
Answer
A. No limit
31
Functional key F9 stands for
Answer
D. Snap on/off
32
Extend is ____________ type of command.
Answer
B. Modify command
33
Command which is used to erase part of an object between two points
Answer
A. Break
34
Which of the following is an igneous rock ?
Answer
D. Basalt
35
Which test is used to determine the rate of wear of stones ?
Answer
B. Attrition test
36
In which process in the manufacturing of brick the clay is brought to a proper degree
of hardness ?
Answer
C. Tempering
37
Which of the following bricks are used as aggregate for concrete in foundation, floors
etc. ?
Answer
D. Fourth class
38
The minimum compressive strength of lime mortar 1 : 3 with Class A lime at the end
of 14 days is
Answer
A. 1.75 N/mm2
39
Burning of cement is carried out in
Answer
C. Rotary kiln
40
Which of the following tiles are conical in shape ?
Answer
B. Guna
41
The alternate dry and wet conditions causes the development of ______ in timber.
Answer
D. Wet rot
42
The size of pin knot is
Answer
A. Upto 6.50 mm dia.
43
The weight of Rose wood after seasoning is
Answer
D. 7900 N/m3
44
Recommended slump of concrete for normal RCC work is
Answer
C. 80 – 150 mm
45
The nominal mix correspond to M7.5 Grade concrete is
Answer
B. 1 : 4 : 8
46
Permissible stress in compression for M20 grade concrete is
Answer
C. 7 N/mm2
47
Maximum Safe Bearing Capacity of soft rock in tonne/m2 is
Answer
A. 45
48
Which of the following foundation is used when hard bearing stratum is at a greater
depth ?
Answer
D. Pile
49
In which bond every header is centrally supported over a stretcher below it ?
Answer
B. Flemish bond
50
A projecting stone which is usually provided to serve as support for joist, Truss
etc.
Answer
A. Corbel
51
Which of the following flooring is suitable for Warehouses, Stores, Godowns etc. ?
Answer
C. Brick
52
The span of a couple roof is limited to
Answer
B. 3.6 m
53
Which of the following is the most common material used as vehicle in a paint ?
Answer
A. Linseed oil
54
An intermediate floor in any storey over hanging and over looking a floor beneath is
Answer
D. Mezzanine floor
55
The site plan shall be drawn to a scale not less than
Answer
D. 1 : 400
56
The area of bathroom shall not be less than
Answer
A. 1.5 m2
57
Minimum width of ramp is
Answer
Question Cancelled
58
How many percentage of the estimated cost is provided for work charged establishment ?
Answer
B. 1½ – 2%
59
Which of the following is not an approximate estimate ?
Answer
D. Detailed
60
The unit of measurement of Steel reinforcement in RCC in MKS system is
Answer
B. Quintal
61
The multiplication factor of painting for both sides of a venetian door
Answer
C. 3.00
62
Density of mild steel is equal to
Answer
C. 7500 kg/m3
63
Which of the following is job overheads ?
Answer
D. Supervision
64
How much quantity of dry materials is required for cement sand mortar for 1 cu.m.
of brick masonry ?
Answer
B. 0.30 cu.m.
65
Which of the following is not included in floor area of a building ?
Answer
C. Walls
66
The value of a property at the end of utility period without being dismantled
Answer
B. Salvage value
67
Which term is used to indicate the decrease or loss in the value of a property due to
use, life etc. ?
Answer
D. Depreciation
68
What is the clear access width to an individual occupancy of a single storeyed building
from the street ?
Answer
A. 1.20 m
69
Which of the following term means side or part of a side of a plot which abuts on a
street ?
Answer
D. Frontage
70
How much percentage of plinth area is taken for calculating carpet area of an office
building ?
Answer
C. 60 – 70%
71
What is the permissible covered area for a plot of area more than 1000 m2 ?
Answer
A. 33% of site area
72
A pier forming part of a wall partially projecting there is
Answer
B. Pilaster
73
What is the minimum vertical distance between any accessible part of the building
and the electric lines of low voltage ?
Answer
A. 2.5 m
74
The first watering before sowing a crop is called
Answer
A. Paleo
75
The amount of water which flows over the surface of earth after all the losses have
taken place is called
Answer
C. Run off
76
The relation between base period, delta and duty is given by:
Answer
A. Δ = 8.64 B/D
77
The dam which is constructed to store water during floods and releases it gradually
at a safe rate when the flood recedes
Answer
C. Detention dam
78
The line on a rainfall map joining places having same average annual rainfall is
Answer
A. Isohyets
79
Which of the following is constructed when the HFL of drainage is higher than canal
bed level ?
Answer
B. Syphon aqueduct
80
The canal which is aligned along a water shed and runs most of its length on a water
shed is
Answer
B. Ridge canal
81
The river training work constructed on either bank of river upstream to protect the
land and property during floods
Answer
C. Marginal bank
82
The structure constructed on a channel to lower down the water level and bed level
of the channel is
Answer
D. Canal fall
83
The sheet of liquid flowing over a notch is known as
Answer
C. Nappe
84
The property of fluid which controls its rate of flow
Answer
B. Viscosity
85
Unit of specific gravity is
Answer
D. No unit
86
Which of the following is an instrument used to measure fluid pressure ?
Answer
A. Manometer
87
What is the unit of pressure in S.I. system ?
Answer
B. Pascal
88
The type of energy possessed by water in an elevated tank is
Answer
A. Potential energy
89
SI unit of force is
Answer
A. Newton
90
A body of mass 10 Kg is moving with a velocity of 2 m/s, then kinetic energy is ______
Kgm/s.
Answer
D. 20
91
If a car travels a distance of 30 m in 10 second, the speed of the car is
Answer
B. 3 m/s
92
If the co-efficient of friction (�) is 0.3 and normal reaction (R) is 10 N, then the frictional
force (F) is
Answer
A. 3 N
93
The stress developed, if a force of 250 N is applied on a rod of area of cross section
50 m2 is __________ N/m2.
Answer
D. 5
94
Mechanical Advantage (MA) of a simple machine is 3 and the load (W) is 9 Kg, then
the effort (P) applied is
Answer
A. 3 Kg
95
In a simple machine, the ratio of distance moved by the effort to the distance moved
by the load is called
Answer
B. Velocity ratio
96
The perimeter of an equilateral triangle is 36 cm, then length of its side is
Answer
B. 12 cm
97
The side of a cube is 7 cm, then its volume is
Answer
D. 343 cm3
98
The value of acceleration due to gravity is
Answer
A. 9.81 m/s²
99
The perimeter of square of side 12 cm is
Answer
C. 48 cm
100
The area of a circle whose radius is 7 cm is
Answer
A. 154 cm2
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.