| Post Name | Tractor Driver Grade.II |
|---|---|
| Department | Agriculture Dvelopment And Farmers Welfare |
| Question Paper Code | 092/2026/OL |
| Category Code | 369/2025, 779/2025, 459/2024 |
| Date of Test | 12 May 2026 |
| Exam Type | Online Examination |
| Total Questions | 100 |
1
The part or parts of a road normally used by vehicular traļ¬c, whether separated from one another by a dividing strip or a diļ¬erence of level or not is
Answer
C. Carriageway
2
The child up to what age is seated in an appropriate child restraint system?
Answer
B. 12 years
3
If a technical defect is discovered in a vehicle while it is being driven, the driver shall
Answer
D. Take the vehicle oļ¬ the road in the quickest possible manner
4
The number of persons a driver of the tractor can carry on the tractor
Answer
A. No person
5
The driver facing the "STOP" sign displayed on the road shall
Answer
D. All the above
6
The maximum speed while towing a vehicle shall not exceed
Answer
C. 25 kilometres per hour
7
The priority within the emergency vehicles shall be
Answer
D. Fire Service Vehicle, Ambulance, Police Service vehicle
8
Road user means
Answer
D. All the above
9
A vehicle shall not be parked on a main road or at a stretch of a road where the notiļ¬ed maximum speed limit is
Answer
A. Fifty kilometres per hour or more
10
On mountain roads and steep roads, where the road is not suļ¬ciently wide to allow the motor vehicles to cross each other freely, the driver travelling downhill shall
Answer
C. Both 1 and 2
11
No person shall be granted a license to drive transport vehicle in any public place unless completing the age of
Answer
C. 20 year
12
A transport vehicle shall not be deemed to be validly registered under the Motor Vehicles Act, unless it carries a valid
Answer
D. Certiļ¬cate of Fitness
13
In respect of any vehicle, the total weight of the vehicle and the load certiļ¬ed and registered by the registering authority as permissible for that vehicle is
Answer
C. Gross vehicle weight
14
License to drive a transport vehicle be eļ¬ective for a period of
Answer
B. Five years
15
When a motor vehicle registered in one State has been kept in another State, for a period exceeding ________ months, the owner shall apply for new registration to the registering authority, within whose jurisdiction the vehicle is then.
Answer
D. 12
16
A permit other than a temporary permit or a special permit shall be eļ¬ective for a period of
Answer
A. 5 years
17
The maximum ļ¬ne a Judicial Court awards for violating provisions of section 129 (Penalty for not wearing protective head gear-section 194D)
Answer
B. Rs. 1,000
18
Which of the following vehicles require installation of Speed limiting device/Speed Governor.
Answer
C. Contract carriage
19
Oļ¬cer authorized to seize and detain that vehicle and make necessary arrangements for the safe custody of that vehicle for non payment of tax
Answer
C. Both 1 and 2
20
If a transport vehicles registered in any State or Union Territories other than the State of Kerala and found operating in the State of Kerala without remitting tax due to Kerala, the tax shall be levied
Answer
B. Double the amount speciļ¬ed in the schedule
21
What does this Traļ¬c sign indicate?
Answer
C. Do not overtake
22
What does this traļ¬c sign indicate?
Answer
B. The height of the vehicle should not exceed three and a half meters
23
What does this traļ¬c sign indicate?
Answer
C. No entry
24
What does this traļ¬c sign indicate?
Answer
D. One way traļ¬c
25
What does this traļ¬c sign indicate?
Answer
C. All motor vehicles prohibited
26
What does this traļ¬c sign indicate?
Answer
A. Narrow bridge
27
What does this traļ¬c sign mean?
Answer
B. Cycle lane
28
What does this traļ¬c sign mean?
Answer
A. School ahead
29
Which category does this traļ¬c sign belong to?
Answer
B. Mandatory
30
What does this traļ¬c sign indicate?
Answer
D. Road widens
31
What is meant by the dotted line and the solid line coming together in the middle of the road?
Answer
D. All of the above
32
What does a white or yellow zig zag line on the road indicate?
Answer
B. It indicates that people are close to crossing the road
33
What does a white or yellow striped median in the middle of the road indicate?
Answer
D. All of the above
34
What does the yellow box junction marking on the road indicate?
Answer
B. A place where the vehicle has to drive without stopping so as not to cause traļ¬c obstruction
35
What does the spaced white line in the middle of the road indicate?
Answer
D. All of the above
36
What does the white line on the side of the road indicate?
Answer
A. A line to identify the sides of the road
37
What does the left arrow in broken lines in the middle of the road indicate?
Answer
B. Overtaking vehicles should get back in line as soon as possible
38
What do the long, spaced white lines in the middle of the road indicate?
Answer
A. Before the curve or the place where more attention is needed on the road
39
What does the striped side marking indicate?
Answer
D. All of the above
40
What does the continuous white line in the middle of the road indicate?
Answer
C. Do not cross the line or overtake vehicles
41
What is P.T.O. in Tractor?
Answer
B. Power Take-oļ¬ stub
42
Rotavator is also known as
Answer
A. Rotary Tiller
43
An example of vehicle daily maintenance
Answer
D. All of the above
44
Which of the following is not a tractor drawn tillage tool?
Answer
D. Plank
45
What is to be checked for low power generation of engine?
Answer
D. Clogged air cleaner
46
The basic purpose of tyre rotator on automobiles is to
Answer
B. Equalize wear
47
Front wheel of tractor is smaller than rear wheel. That helps __________
Answer
C. To take sharp turnings
48
Ploughing is done to __________
Answer
D. All of the above
49
Which transmission unit allows the inner driving road wheel to rotate slower than the outer wheel but still maintain a drive to both wheels?
Answer
A. Diļ¬erential
50
Colour of tractor's tail light is _______
Answer
B. Red
51
Given the name of three measuring instruments. Which among them can be used for measuring the bore of a cylinder? (i) Telescopic gauge (ii) Screw gauge (iii) Feeler gauge
Answer
A. (i) Only
52
Which of the following statements is True in the case of calipers?
Answer
C. The legs of the inside calipers are curved outwards.
53
The lease count of a vernier calipers is __________
Answer
Question Cancelled
54
Which of the following is a Power Tiller manufacturer in Kerala?
Answer
D. KAMCO
55
If the crankshaft of an engine rotates at 1600 rpm, the speed of cam shaft will be
Answer
B. 800 rpm
56
In a typical piston, where are oil drain holes found?
Answer
C. On lower ring grooves
57
Which among the following can be the ļ¬ring order and ļ¬ring interval of a four-cylinder diesel engine?
Answer
D. 1-3-4-2 and 180
58
Compression ratio of an engine is
Answer
B. (Swept Volume + Clearance Volume) / Clearance Volume
59
The exhaust valve of a four-stroke engine usually starts opening ...
Answer
A. Just before BDC
60
A āSquare Engineā is an engine with ________
Answer
D. Stroke and bore equal
61
Which of the following will happen when the foot pedal for clutch is depressed?
Answer
B. Pressure plate moves away from clutch plate
62
The function of diļ¬erential lock in a two-wheel drive tractor is ________
Answer
A. To drive both the rear wheels at the same speed
63
With respect to rear mounted PTO types of tractors, which among the following statements are correct? 1 For Type I, there will be 6 straight splines with speed as 540 +/- 10 2 For Type 2, there will be 21 straight splines with speed as 1000 +/- 25 3 For Type 3, there will be 21 involute splines with speed as 1000 +/- 25
Answer
D. 1 and 3 are correct
64
In a tractor with planetary ļ¬nal drive system. which gear is driven by the input from diļ¬erential?
Answer
A. Sun Gear
65
Which of the following characteristics is typically associated with a four-wheel-drive (4WD) tractor compared to a two-wheel-drive (2WD) tractor?
Answer
D. Similar tread pattern on all wheels
66
For tractor trailers upto 5T capacity, the overall length of the platform and width of the trailer, shall not exceed ____________ respectively
Answer
B. 5 m and 2.5 m
67
The process of adding additional weight to tractor for increasing traction is called
Answer
A. Ballasting
68
The horsepower which is available in a tractor to pull loads is known as
Answer
D. Drawbar horsepower
69
To ensure stable working conditions of a tractor, while using three-point linkage, it is recommended that the vertical convergence distance is not less than ____________ the tractor wheelbase.
Answer
C. 0.9 times
70
Which of the following statements accurately describes the ampere-hour (Ah) rating of a battery?
Answer
B. The Ah rating represents the total charge capacity of a battery over time
71
Calibration of a seed cum fertilizer drill is done for (i) To ensure proper depth of seeding (ii) To ensure proper seed rate (iii) To ensure proper fertilizer rate
Answer
B. All except (i) are correct
72
What does ātoe-inā refer to with respect to front axle adjustment of tractors?
Answer
B. The wheels pointing inward towards the centerline of the vehicle
73
Tandem master cylinder in braking system consists of __________
Answer
D. Two cylinders and two reservoirs
74
What does the term "ply ratingā refer to in tractor tires?
Answer
C. An index of tire strength
75
The rear wheel track of most of the indigenous tractors can be altered by (i) Changing wheel ā rim positions (ii) Interchanging rear wheels.
Answer
C. Both (i) and (ii) are correct
76
Which type of road signal shows blue circle with white symbol?
Answer
B. Mandatory signal
77
The least count of an Universal vernier caliper is ___________
Answer
C. 0.02 mm
78
The tool used to cut internal threads in a hole is
Answer
B. Taps
79
The capacity of a lead acid battery depends upon ___________
Answer
D. All of the above
80
__________are used mostly in the application of rectifying AC to DC.
Answer
B. Diodes
81
__________is an instrument that indicate the distance travelled by a vehicle.
Answer
C. Odometer
82
_________is a safety equipment, before starting the work under the lifted vehicle
Answer
C. Axle stand
83
Which type of exhaust emission is controlled by EGR system?
Answer
C. Oxides of Nitrogen
84
PCV valve is ļ¬tted in ________ System.
Answer
C. Crankcase emission control
85
The distance between the axis of the piston pin and top of the piston crown is called _____________
Answer
B. Compression height
86
In MPFI engines, the fuel is sprayed in ______________ Stroke
Answer
A. Suction
87
_________ helps to bring the cold engine to the operating temperature quickly.
Answer
C. Thermostat valve
88
The minimum number of ignition coil required in a distributorless ignition system for a 4 cylinder engine is ________
Answer
B. 2
89
The chassis of an automobile consists of _________
Answer
D. All of the above
90
______is the weight of vehicle components between the suspension and the road surface.
Answer
A. Unsprung weight
91
Factors aļ¬ecting the wheel alignment are __________
Answer
D. All of the above
92
Hydraulic brakes work under the principle of _________
Answer
B. Pascalās law
93
The center gear of an epicyclic gear set is called ___________
Answer
A. Sun gear
94
Solenoid switch pull-in winding is connected with the __________
Answer
B. Starter switch
95
Crash sensors are used in ___________ system
Answer
C. Air bag
96
The catalyst used in the catalytic converter for oxidising HC and CO is ___________
Answer
C. Platinum
97
Intake Air Temperature sensor works on the basis of __________ principle
Answer
B. Thermistor
98
__________is used to indicate the problems in the engine management system of MPFI system.
Answer
C. Malfunction indicator lamp
99
______________sensor is used to monitor the injection timing and ignition timing of the MPFI engine.
Answer
B. Camshaft position sensor
100
__________can be used to determine the exact location of a vehicle on the earth's surface.
Answer
D. GPS
Discussion
Ask a doubt or share a tip.
No comments yet ā start the discussion.