| Post Name | TRADESMAN (CARPENTRY) |
|---|---|
| Department | TECHNICAL EDUCATION |
| Question Paper Code | 201/2015 |
| Date of Test | 27 October 2015 |
| Medium of Question | ENGLISH |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
‘The size of a hammer is generally specified by :
Answer
D. Weight of its head
2
Name the chisel which has a thicker and stronger blade than ordinary firmer chisel.
Answer
C. Registered firmer chisel
3
While sawing with a Hand saw, the sight of eye should be :
Answer
D. Directly above the saw
4
Hard Woods has generally type of cells.
Answer
C. Two
5
Fevicol-SH isa ___ type of glue.
Answer
C. Polyvinyl acetate
6
Dowels are generally made of :
Answer
A. Hard Wood or Bamboo
7
The spiral grooves which run in the length of the drill is called :
Answer
D. Flutes
8
The reading accuracy of a Steel Rule is :
Answer
A. 0.5 mm
9
A Phillips head screw has :
Answer
C. A cruciform slot
10
Find the volume of timber piece having 2 metre long, 20 centimetre width and 30 millimetre
thickness.
Answer
A. 0.02 cubic metre
11
Name the defect caused by a limb or branch being cut through during the process of sawing
up the log.
|
Answer
C. Knot
12
Name the spanner usually supplied with machine tools for a specific purpose,
Answer
A. Single ended spanner
13
Find the cost of a 20 mm. plywood having 8 feet long and 4 feet wide at the rate of 7 60.00
per square feet.
Answer
B. % 1920
14
Ina thickness planer, the table is provided at :
Answer
B. Below the revolving head
15
Ina multiply board, the number of core plies are :
Answer
C. Threeormore
16
A steel bar cuts with a Hack - saw, it is a metal cutting method of :
Answer
D. None of these
201/2015 4 A
Pn eke Caen a der ;
17
The distance of a drill advances into the work in one complete rotation is called :
Answer
A. Cutting feed
18
The special rule intended for pattern maker is :
Answer
B. Contraction rule
19
The horizontal distance between the internal faces of walls or supports is called :
Answer
D. Span
20
Name the horizontal platform between two flights of a stair.
Answer
D. Landing
21
Name the saw which has a very fine blade held in a rectangular long frame of |
300 to 500 mm.
Answer
C. Fret saw
22
Oil stone slips or slip stones are :
Answer
B. Oil stones of various shapes
23
Name the tool used for checking the thickness of metal sheets.
Answer
D. Standard wire gauge
24
A plywood has at least ___ number of plies or veneers.
Answer
C. Three
25
Dry-rot is a decay caused by :
Answer
C. Fungus
26
Name the saw suitable for cutting along the grains of timber piece.
Answer
A. Rip saw
27
Name the material used to make drill bits.
Answer
B. High speed steel
28
Ina surface planer, for most cuts, the rear table or out - feed table is set at :
Answer
D. even with the cutting edges of knives
29
The total length of a collapsible or zig-zag rule is :
Answer
B. 100 cms
30
The main ingredients of French Polish are :
Answer
C. Shellac and mythelated spirit
31
Blockboard is a manufactured board with a core of :
Answer
B. Wooden strips
32
The horizontal member on the bottom of a door or window frame is called :
Answer
D. Sill
33
One metre is:
Answer
A. 1000 mm
34
A core used in a casting industry is a type of :
Answer
B. Sand mould
35
The horizontal support provided on a Batten door is called :
Answer
D. Ledge
201/ 2015 6 A
" rs
36
Name the tool suitable for measuring a longer and convex wooden edge.
Answer
B. Tape measure
37
The size of a carpenter vice is specified by :
Answer
A. Width of its jaw
38
Name the tool suitable for marking a circle of 110 cm radius on a wooden board. |
Answer
C. Trammel points
39
Name the plane suitable for producing a long, true and straight surface or edge.
Answer
C. Trying plane
40
Name the tool suitable for testing the flatness of a door style, while planing.
Answer
D. Try square
41
It form a seat to support and locate the core in the mould sand during casting :
Answer
B. Core print
42
Aluminium oxide is one of the artificial abrasive mineral, name another artificial one.
Answer
B. Silicon Carbide
43
Hollow chisel mortisers are generally available with hollow chisel size from :
Answer
B. 6mmtoli mm
44
Horizontal Band Saws are generally used for :
Answer
D. Cutting large diameter logs.
A z 201/2015
{P.T.O.}
) !
45
Name the tool used for cutting internal threads, |
Answer
A. Hand taps
46
Ina vernier caliper the measuring accuracy is upto :
Answer
D. 0.02 mm
47
Band saw blades are generally joined by :
Answer
A. Brazing
48
Name the allowance provided on all vertical surfaces of a pattern is :
Answer
A. Draft or taper allowance
49
A three piece pattern require a moulding box with three parts, The middle one is called :
|
Answer
A. Cheek box
50
The horizontal wooden member placed on principal rafters to support the common rafters is
| called :
Answer
A. Purlin
51
The window which projects outside the external wall is called :
Answer
D. Bay window
52
Name the tool used for boring large, deep holes in timber,
Answer
D. Hand auger
53
Bradawl is used for :
Answer
B. Making small holes |
54
Name the tool suitable for marking the width of hinges on door jambs.
Answer
C. Butt gauge
55
The process of bevelling the top of a drilled hole is called :
Answer
A. Counter sinking
56
Name the plane suitable for making a groove on the edge of a timber piece. |
Answer
B. Plough plane
57
Total length of a Four - Fold rule is : |
Answer
D. 60cm
58
Name the tool suitable for pulling out a large number of big nails.
Answer
D. Crowbar
59
Ina tenoning machine, which revolving head can be raised or lowered ?
Answer
C. Both
60
Name the oil preservative among the following.
Answer
D. Creosote
61
Name the sander suitable for sanding hollows and irregular curves.
Answer
A. Spindle sander
62
Ina circular saw machine, table, the grooves are made for :
Answer
C. To support and guide mitre gauge.
63
The purpose of timber seasoning is not to reduce.
Answer
C. Hardness
64
Ina Plumb bob, the diameter of the wooden block is : |
|
Answer
A. Slightly greater than diameter of cylinder.
|
65
In an adjustable Rebate plane, the width regulating fence is provided at :
|
Answer
D. On the bottom of the plane,
66
Name the bit suitable for boring a skewed hole or a flat bottom hole.
Answer
C. Forstner bit
67
The density value of timber are determined at a specific moisture content of :
Answer
A. 12%
68
The angle of point in a centre punch is :
Answer
C. 90 degree
69
Name the Tree having short trunk and large branches.
Answer
A. Shisham
70
Name the part of a tree which is responsible to form new bark on the outside and new
sapwood on the inside.
Answer
C. Cambium layer
71
Name the simplest and most economical method of cutting up a log into boards.
Answer
D. Live sawing
72
When cracks develop between adjacent annual rings, it is called :
Answer
B. Cup shake
73
Name the strongest joint, most suitable for making a table drawer.
Answer
D. Lapped dovetail joint
74
One cubic metre is :
Answer
B. 35.315 cft.
75
The plane used for providing a key for glue is : |
Answer
B. Toothing plane
76
The grinding angle of chisels and plane irons are :
Answer
C. 20 to 25 degree
77
Name the chisel suitable for cutting corners less than 90 degree.
Answer
D. Bevel edge firmer chisel
78
Which cramp is works on lever principle to hold work to the bench ?
Answer
B. Bench hold fast
79
Convex or hollow planes are included in the group of :
Answer
B. Moulding planes
!
80
Name the equipment used to plane the end side of timber without breaking the edges.
|
Answer
B. Shooting board
81
Guindy Deer Park is in :
Answer
B. Chennai
82
Chennai is situated on the bank of river :
|
Answer
A. Coovam
83
Which place is known as the ‘City of Pearls’ ?
Answer
D. Hyderabad
84
Veerbhumi is the Samadhi of :
Answer
C. Rajiv Gandhi
85
Which soil is known as ‘regur’ soil ?
Answer
A. Black soil
86
Which forests are also called as monsoon forests ?
Answer
C. Deciduous forests
87
Which of the following dams is built across the river Mahanadi ?
Answer
B. Hirakud
88
A Rabi crop:
Answer
D. Wheat
201/2015 12 A
'
89
The statement
“| want world sympathy in this battle of Right against Might” is associated with :
Answer
D. Gandhi's Dandi March
90
Who among the following had launched the paper ‘Qaumi Awaz’ ?
Answer
A. Jawaharlal Nehru
91
The memoir entitled ‘Bapu ; My Mother’, was written by :
Answer
C. Manubehan
92
Which one of the following sessions of Indian National Congress was Presided over by |
Jawaharlal Nehru ?
Answer
B. Lahore Session, 1929
93
India’s contribution to the world fruit production is :
Answer
A. 10%
94
Who among the following led the ‘Vimochana Samaram’ ?
Answer
D. Mannath Padmanabhan
95
The Diwan, who depoted Swadeshabhimani Ramakrishna Pillai :
Answer
C. P. Rajagopalachari
96
The National Award for Best Actor from Malayalam film for the first time was won by :
Answer
B. PJ. Antony
97
The founder of Atma Vidhya Sangam :
|
Answer
D. Vagbhadanandan
98
In the Union Cabinet of India, the Union Minister for Environment is : |
Answer
C. Prakash Javadekkar
99
The best seller in 2014, the famous book “The Accidental Prime Minister”. The making and
unmaking of Manmohan Singh is written by :
Answer
A. Sanjay Baru
100
Who is the present Chairman of Public Accounts Committee (PAC) of the Indian
Parliament ?
Answer
B. Prof. K.V. Thomas
|
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.