| Post Name | Tradesman(Survey), Surveyor Grade.II |
|---|---|
| Question Paper Code | 063/2024 |
| Category Code | 418/2023, 683/2023 |
| Date of Test | 22 May 2024 |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
Which drawing sheet is most convenient for the class room drawing?
Answer
B. A2
2
Which pencil is used for construction lines, dimension lines, centre lines, section lines etc.?
Answer
D. 2H
3
Which range of lettering is generally used for sub-titles and heading?
Answer
C. 3 to 6 mm
4
Lines of hidden edges are drawn as :
Answer
D. Dashed thin
5
In which system of dimensioning, all dimensions are placed from the bottom of the drawing
sheet?
Answer
A. Unidirectional system
6
In which the quadrilateral have only two sides are parallel and the four angles are different?
Answer
C. Trapezoid
7
When the section plane is inclined to the axis of the cone and is parallel to one of the
generators the section is?
Answer
A. Parabola
8
Which is the part of the circle or area bound by the arc and chord?
Answer
D. Segment
A 3
9
An actual length of 5 m of a room is represented by 25 mm length on drawing. Then
Representative fraction of drawing is :
Answer
D. 1/200
10
The elevation of a cylinder whose axis is parallel to VP and perpendicular to HP is :
Answer
D. Rectangle
11
What is the graphical representation of features on the earth surface or below the earth
surface on a horizontal plane in a small scale is?
Answer
B. Map
12
Preliminary survey is used for :
Answer
D. Collecting more precious datas and choose the best location of the work and to
estimate the quantities and cost
13
The limit of plane survey is :
Answer
Question Cancelled
14
The main principle of survey is work from the whole to part for :
Answer
A. Prevented accumulation of errors
15
Which tape is preferable for the highest precision work and used in measurement of base line
to triangulation in the city work?
Answer
C. Invar Tape
16
Which measurements are taken at right angles to the chain line of a survey work is?
Answer
A. Perpendicular Offsets
17
The limit of error in 30m Chain as per BIS :
Answer
B. ± 8 mm
18
The length of a line measured with a 20 m chain was to be 250 m. Calculate the true length
of the line if the chain was 10 cm too long :
Answer
C. 251.25 m
19
Which instrument is used to reproduce plans to a different scale is?
Answer
B. Pentagraph
20
A tape may be too long or an angle measuring instrument may be out of adjustment. Then
such type of error comes under which source of error?
Answer
A. Instrumental
21
In survey work the reciprocal ranging is applicable for :
Answer
Question Cancelled
22
The size of field book is :
Answer
B. 20 × 12 cm
23
In sexagesimal system, 1 circumference =
Answer
A. 360°
24
__________ is any convenient direction towards a permanent mark or signal.
Answer
C. Arbitrary meridian
25
The lines of force of earth’s magnetic field run generally from :
Answer
A. South to North
26
In surveyor’s compass the graduations are in :
Answer
B. Quadrantal bearing
27
The magnetic bearing of a line AB is S 28º 30’ E, calculate the true bearing if the declination
is 7º 30’ W :
Answer
A. S 36º 0’ E
28
Convert the quadrantal bearing N 12º 24’ E to whole circle bearing :
Answer
B. 12º 24’
29
The fore bearing of a line AB is N 86º 12’ W find its back bearing :
Answer
B. S 86º 12’ E
30
The bearing of a line AB is measured from A towards B, it is known as :
Answer
A. Fore bearing
31
The horizontal angle between the true meridian and the magnetic meridian is known as :
Answer
A. Magnetic declination
32
The local attraction at a particular place can be detected by observing the _________ of each
line and finding its difference.
Answer
C. Fore bearing and Back bearing
33
Inaccurate levelling of the compass box is a ___________ error.
Answer
B. Personal
34
The extent of daily variations depend upon :
Answer
D. All of these
35
____________ is the process of determining the plotted position of the station occupied by
the plane table, by means of sights taken towards known points, locations of which have
been plotted.
Answer
C. Resection
36
The __________ is used to orienting the plane table to magnetic north.
Answer
D. Compass
37
Location of the position on the plan, of the station occupied by the plane table by means of
observations to two well defined points whose positions have been previously plotted on the
plan is known as :
Answer
B. Two - point problem
38
__________ is the process of putting the plane - table into some fixed direction so that line
representing a certain direction on the plan is parallel to that direction on the ground.
Answer
A. Orientation
39
Methods of plane tabling can be divided into __________ distinct heads.
Answer
D. 4
40
Which of the following is the permanent adjustment of dumpy level?
Answer
C. Two peg method
41
In contouring horizontal equivalent depends upon :
Answer
D. Slope of the ground
42
Mean Sea Level (M.S.L.) is the average height of the sea for all stages of tides. It is the
average of hourly tides for a long period of _________ years.
Answer
D. 19
43
What is the combined correction for curvature and refraction for a distance of 3 km?
Answer
B. 0.6057 m
44
In the case of levelling across a river or lake, which type of levelling is used?
Answer
C. Reciprocal levelling
45
In plotting the Longitudinal section (profile levelling), the vertical scale for showing the
reduced level is enlarged to __________ times the horizontal scale.
Answer
A. 10
46
A set of V-shaped contours with higher value contours inside the bent represents
Answer
D. Ridge
47
What is the controlling factor for locating a highway or canal in a contour map?
Answer
C. Gradient line
48
What is the quantity of cutting given the ground level as 232.50 and formation level
is 231.10?
Answer
B. 1.40
49
When the sights are long _________ types of staff used for levelling work.
Answer
D. Target staff
50
Which surface is normal to the direction of gravity at all points?
Answer
Question Cancelled
51
Which level is that the line of sight remains horizontal once the operator has roughly levelled
the instruments?
Answer
C. Auto level
52
What is rise or fall, if back sight reading taken on B.M is 2.045 m and intermediate sight on
point = 2.68 m?
Answer
B. – 0.635 fall
53
Which instrument is used for establishing grade contour?
Answer
B. Abney level
54
What is S in the formula A = Bd + Sd²?
Answer
C. Side slope
55
The latitude and departure of any point with reference to the preceding point are called :
Answer
A. Consecutive co-ordinate
56
Which method of theodolite traversing, the magnetic bearing of only the first line is
measured? The magnetic bearing of all other lines are determined indirectly:
Answer
A. Fast needle method
57
What are the fundamental lines of theodolite?
(1) Horizontal axis
(2) Line of collimation
(3) Axis of telescope
(4) Slant line
Answer
B. (1), (2) and (3)
58
What is the least count of stadia rod?
Answer
B. 0.001 m
59
What is the distance from mid point of the curve to point of inter-section?
Answer
C. External distance
60
What formula for length of long chord?
Answer
B. 2R sin Δ 2
61
The axis about which the telescope and the vertical circle of the theodolite rotated in the
vertical plane is called :
Answer
A. Trunnion axis
62
What is the tacheometric equation for distance while the line of sight is horizontal and staff
is held vertically?
Answer
B. D = (f/i)s + (f + d)
63
Which method is suitable for closed traverse in theodolite survey?
Answer
D. Included angle method
64
The component length measured perpendicular to the reference Mendian is called :
Answer
B. Departure
65
The DGPS technique is based on using atleast ___________ GPS receivers.
Answer
A. 2
66
In GPS survey, RTK stands for :
Answer
C. Real Time Kinematic
67
Which instrument is the combination of Electronic Theodolite and electronic distant meter?
Answer
B. Total Station
68
The fundamental measurements with the Total Station are horizontal angle, vertical angle
and :
Answer
C. Slope Distance
69
Which projection uses the equidistant parallel lines for showing the meridians?
Answer
D. Cylindrical Projection
70
Which is the science of acquiring information about the earth’s surface without actually being
in contact?
Answer
C. Remote Sensing
71
Which is an Oceanographic device for flow of measurement?
Answer
A. Current Meter
72
Which is the most accurate method of locating sounding?
Answer
B. Cross Rope
73
Which Line type is available when you start a new drawing in AutoCAD?
Answer
B. Continuous
74
Which command do you use to draw a circle in isometric drafting?
Answer
C. Ellipse
75
To switch isoplane, you press :
Answer
B. F5
76
________________ command is used to restore all entities erased by the most recent Erase
command.
Answer
A. OOPs
77
Which is the short cut key of the text style?
Answer
C. ST
78
File, Edit, View etc. Are easily available in AutoCAD from?
Answer
A. Menu bar
79
Which co-ordinate system is used in AutoCAD if we know the precise X and Y values in the
point from the origin?
Answer
B. Absolute co-ordinate system
80
Which of the following software is limited for Auto CAD installation?
Answer
D. Windows 10
81
Unit of heat in MKS :
Answer
B. Joule
82
1 Hectare = ____________ Are.
Answer
C. 100
83
Find 37.698/1000.
Answer
A. 0.037698
84
Melting point of Molybdenum is :
Answer
A. 2620°C
85
1 Newton = ____________ dyne.
Answer
Question Cancelled
86
1 + tan²θ =
Answer
A. sec²θ
87
cot(90 + θ ) =
Answer
D. − tan θ
88
Example for a third order lever :
Answer
D. Forceps
89
The property of a metal to resist the effect of tensile forces :
Answer
C. Tenacity
90
The type of caste iron which cannot be welded :
Answer
D. White cast iron
91
Density of water in gm cm3 :
Answer
Question Cancelled
92
What will be the velocity of the body, when the body travels a distance of 180 m in a straight
line in 20 seconds?
Answer
B. 9 m sec
93
Which is the most powerful neutral refractory material?
Answer
B. Chromite
94
The Lime containing more than 30% of clay is known as :
Answer
C. Poor lime
95
Well grade sand should be pass BIS no.480 and should not pass BIS No. _____________ sieve.
Answer
A. 15
96
Wood absorbing water vapours from air is known as :
Answer
B. Hygroscopicity
97
What is the name of first watering given to a crop, when the crop is a few centimeter height?
Answer
D. Kor watering
98
Road constructed to secure access from a road to a private property is known as :
Answer
B. Drive way
99
The permissible gradient in the alignment of highway is known as :
Answer
C. Ruling gradient
100
How much percentage of Centage is added in estimate?
Answer
D. 10% – 15%
———————
063/2024 14 A
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.