| Post Name | Work Superintendent (NCA- Dheevara) - Agriculture Development and Farmer's Welfare (Soli Conservation Unit) |
|---|---|
| Question Paper Code | 051/2022 |
| Category Code | 320/2020 |
| Date of Test | 10 May 2022 |
| Medium of Question | ENGLISH |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
Size of Bo-drawing board in mm is _______
Answer
A. 1500 Γ 1000 Γ 25
2
Trimmed size A4 drawing sheet in mm is ______
Answer
D. 210 Γ 297
3
In lettering the height to width ratio for the letter 'w' is
Answer
Question Cancelled
4
In _____ system of dimensioning all the figures and notes are lettered horizontally
and are read from the bottom of the drawing.
Answer
B. Unidirectional
5
Which of the following is an enlarged scale?
Answer
A. 2:1
6
A plane figure having 10 sides is known as __________
Answer
D. Decagon
7
Which type of line is applicable for dimension lines?
Answer
B. Continuous thin
8
In third angle projection plan is placed
Answer
A. Above front view
9
In 1st angle projection right side view is placed
Answer
C. Left side
10
Hyperbola, Parabola and the ellipse are known as
Answer
D. Conic sections
11
The main principle of surveying is to work from
Answer
D. Whole to part
12
Length of one link in 30 mtr. chain
Answer
B. 20 cm
13
One hectare is _____ acres.
Answer
C. 2.471
14
The size of field book is
Answer
C. 20 Γ 12 cm
15
At magnetic poles, dip of a magnetic needle is
Answer
D. 90o
16
The bearing of a line taken in the progress of the survey is ___________
Answer
C. Fore bearing
17
If the WCB of a line is 270o its reduced bearing is
Answer
B. S 90o W
18
The size of a theodolite is fixed by measuring
Answer
A. Diameter of graduated circle of horizontal plate
19
Accurate centering of a plane table is done by
Answer
B. Plumbing fork
20
The working edge of an alidade is known as _______
Answer
A. Fiducial edge
21
Arithmatical check used while taking reduced level
Answer
A. Ξ£ B.S. β Ξ£ F.S. = Last RL β Ist RL
22
Assumed level surface from which vertical measurements are measured is _______
Answer
B. Datum
23
An imaginary line which joints the points of same elevations in the ground is called
Answer
B. Contour
24
A fixed point of known elevation is called _______
Answer
C. Benchmark
25
An EDM is the major part of _________
Answer
D. Total station
26
Full form of CAD
Answer
D. Computer aided design
27
AutoCAD command for boundary
Answer
B. BO
28
MO stands for which command in autoCAD?
Answer
D. Properties
29
_____ Tool bar is icons in autoCAD to work with Copy, Mirror, array, offset, move etc.
Answer
D. Modify tool bar
30
_______ generate text only and _______ would generate vector graphics
Answer
A. Printers, plotters
31
_______ provide one of several customizable ways to start commands and change
settings
Answer
A. Tool bars
32
PL is a command for ______ in AutoCAD
Answer
C. Polyline
33
The command for polygon is ____ in AutoCAD
Answer
C. POL
34
Crystalline rocks formed due to slow cooling of magma.
Answer
B. Granite
35
A temporary structure in which bricks are burnt once at a time
Answer
A. Clamp
36
The building bricks can resist temperature up to,
Answer
C. 1220oC
37
The minimum thickness of machine made tiles is,
Answer
A. 10 mm
38
The process of burning limestone is called,
Answer
C. Calcination
39
The percentage of silica in cement ranges from
Answer
B. 18% to 25%
40
A type of cement containing small percentage of Gypsum
Answer
D. Quick setting cement
41
Cement used for emergency repair work and underwater constructions is
Answer
D. Quick setting cement
42
The process of maintaining moisture and temperature of freshly placed concrete for
proper hardening is called
Answer
B. Curing
43
The separation of course aggregate from concrete mix is called,
Answer
A. Seggregation
44
The height of slump for R.C.C. slab and beam in millimeter should be,
Answer
B. 50 to 100
45
The inner part of a timber surrounding the pith, which is dark in colour, compact and
strong,
Answer
C. Heartwood
46
A natural defect caused by the rupture of tissues resulting in partial or complete
separation of the fibres along the grain.
Answer
A. Shakes
47
A board formed by three or more layers of veneers is called
Answer
C. Plywood
48
A small groove cut underside of a structure to discharge the rain water without trickling
down to the wall,
Answer
B. Throating
49
A masonry similar to coursed or random rubble masonry except that no mortar is used
to bond the stones together,
Answer
B. Dry Rubble masonry
50
A brick part which is obtained by cutting a brick lengthwise
Answer
A. Queen closer
51
A rafter shorter than the common rafter is known as
Answer
B. Jack Rafter
52
A concrete floor finished with special type of aggregates of marble
Answer
A. Terrazo floor
53
The phenomenon appeared on plastered surface in whitish patches and produce ugly
appearance
Answer
C. Efflorescence
54
According to use and occupancy Type B building refers to,
Answer
A. Educational building
55
The minimum side open space provided for building upto a height of 10 meters is
Answer
C. 1.5 m
56
The ratio between total covered area of all floors to the plot area is
Answer
Question Cancelled
57
The minimum depth of foundation below ground level is
Answer
C. 60 cm
58
The minimum clear headroom for residential building is
Answer
B. 2.20 m
59
The effect produced by deriving maximum benefit from the minimum dimensions of
the room is,
Answer
D. Roominess
60
Aspect desirable for kitchen is
Answer
C. East
61
In detailed estimate the contractor's profit should be taken as
Answer
A. 10%
62
Decrease or Loss in the value of a property due to structural deterioration
Answer
B. Depreciation
63
Plan prepared for major project work like Road, Irrigation, sanitary works etc. is
Answer
C. Index plan
64
Rate of various works prepared and maintained by engineering department in the
form of printed books is,
Answer
A. Schedule of rate book
65
An estimate prepared from practical knowledge, experience and from cost of similar
work is
Answer
B. Preliminary estimate
66
Unit of measurement of plastering is
Answer
B. M2
67
1440 Kg volume of cement equals to
Answer
D. 30 bag cement
68
The normal Lead and Lift of earthwork is
Answer
A. 30 m and 1.5 m respectively
69
The capacity of doing work by a labour per day in the form of quantity is
Answer
B. Task work
70
The value of a property at the end of its useful life without dismantling
Answer
B. Salvage value
71
The volume of dry material required for one cubic meter of wet concrete is
Answer
A. 1.54 m3
72
The multiplying constant for painting doors and windows fully panelled for both
side is
Answer
C. 2.25
73
No deduction is made for brickwork for opening up to
Answer
B. 0.10 sq.m
74
The total depth of water required by a crop during the entire crop period is
Answer
B. Delta
75
Fall of moisture from the atmosphere to earth
Answer
A. Precipitation
76
A barrier constructed across the river to raise the water level is
Answer
C. Weir
77
The opening provided in the body of a weir to remove silt is
Answer
D. Scouring sluices
78
The margin provided to prevent overtopping of dam during flood, between the F.R.L.
and the top of dam is
Answer
C. Free board
79
A cross drainage work where the drain pass over the canal without lowering the bed
level of the canal
Answer
B. Super passage
80
Excessive moisture present in the soil, causing the soil non-productive and anaerobic
condition is
Answer
C. Waterlogging
81
A canal which is active throughout the year is
Answer
B. Permanent canal
82
An hydraulic structure disposes surplus water from the reservoir is
Answer
C. Spill way
83
Structures constructed transverse to the river flow and extended from bank into
the river
Answer
B. Spurs
84
Simplest form of instrument used for measuring high as well as negative pressure
Answer
B. Simple manometer
85
The property of water which enables it to resist tensile stress
Answer
C. Surface tension
86
The energy possessed by a liquid particle by virtue of its position
Answer
B. Potential energy
87
A flow of liquid in which each liquid particle does not have a definite path and the path
of individual particle also cross each other
Answer
C. Turbulant flow
88
An apparatus for finding out the discharge of a liquid flowing in a pipe
Answer
C. Venturimeter
89
One metric Horse Power is equal to _______ Watts.
Answer
B. 735.5
90
Maximum size
Answer
A. rea) of the circle that can be cut from a square sheet of size
100 mm is
91
A lead pellet of mass 5g leaves an air gun with a velocity of 60 m/s. What is the
magnitude of Potential Energy stored by the spring of air gun?
Answer
D. 9 J
92
The ratio between change in cross-sectional area of a material to its original
cross-sectional area is
Answer
C. Lateral strain
93
Circumference of a circle is 314 cm, then its area is .........
Answer
A. 2500Ο cm2
94
A load of 12000 N acts on a hollow pipe of external diameter 20 mm and internal
diameter 16 mm. Then the compressive stress is ___ N/mm2.
Answer
C. 106.16
95
Which one is a vector quantity?
Answer
B. Velocity
96
75 m3 is equivalent to ..... cm3.
Answer
D. 75000000
97
How many litres of water a cylindrical vessel of radius 50 cm and height 100 cm can
hold?
Answer
C. 785
98
Mechanical Advantage is the ratio of ______
Answer
B. Load to effort
99
In a cantilever beam the Bending Moment at the free end is
Answer
A. 0
100
A force of 50 kg is required to pull a weight of 500 kg on a horizontal plane.
The co-efficient of friction is
Answer
C. 0.1
Discussion
Ask a doubt or share a tip.
No comments yet β start the discussion.