| Post Name | WORK SUPERINTENDENT/ TRACER etc..- AGRICULTURE etc... |
|---|---|
| Question Paper Code | 068/2021 |
| Category Code | 643/2017, 244/2018, 399/2020, 485/2020 |
| Date of Test | 31 July 2021 |
| Medium of Question | ENGLISH |
| Exam Type | OMR Examination |
| Total Questions | 100 |
1
Cumulative errors that are proportional to:
Answer
B. L
2
_________ are the ends of the survey lines which command the boundaries of the
survey.
Answer
B. Main station
3
The offset should not be longer than
Answer
C. 15 m
4
In optical square the angle between the first incident ray and the last reflected ray is
_________ the angle between them the two mirrors.
Answer
B. twice
5
For compass survey the direction from a survey station to some well defined
permanent object, or the first line of survey is known as
Answer
C. Arbitrary bearing
6
The following are the bearing of the line AB and AC : AB N15 15E, AC N87 10E.
Calculate the angle BAC.
Answer
B. 71° 55�
7
The image formed on the plane of cross hair by the objective is
Answer
C. Real and Inverted
8
The method chiefly used for locating the details from stations, which have been
previously established by triangulation
Answer
D. Traversing
9
The absence of Chromatic Aberration is known as
Answer
B. Achromatism
10
For locating the river which method of plane table is used ?
Answer
B. Intersection
11
The effect of curvature is to cause the objects sighted appear ___________ than
they really are
Answer
B. Lower
12
The effect of refraction is
Answer
A. Not constant
13
In total station data is stored in
Answer
C. Micro Processor
14
The minimum clearance kept between the Grillage beam in Grillage foundation is
Answer
B. 8 cm
15
The pile anchor down the structure subjected to uplift pressure due to overturning
moment
Answer
B. Uplift pile
16
Safe permissible load on coursed rubble in cement mortar
Answer
Question Cancelled
17
The depth of lintel should be
Answer
B. 8 cm
18
The diameter of bar used in lintel for span 1.5 to 2 m
Answer
B. 10 mm
19
The sloping surface used to provide an easy connection between floor
Answer
B. Ramp
20
What is the alignment of cross joint along the plumb line ?
Answer
B. Perpend
21
The process of filling hollow space of walls before plastering is known as
Answer
D. Dubbing out
22
Additional Pozzolana to ordinary portland cement increases
Answer
B. Shrinkage
23
Wrought iron is manufactured from pig iron by
Answer
D. All the above
24
Temporary structure to support arch during its construction
Answer
D. Centering
25
The straight line which is generating the surface of the cone is called
Answer
A. Generator
26
The point of contact between the focal sphere and section plane is called
Answer
D. Focus
27
For reducing and enlarging drawing from an available drawing without converting
numerical value is called
Answer
B. Proportional Divider
28
In first angle projection object is situated ________ of the observers eye and the
plane of projection.
Answer
B. In between
29
A solid having four equal equilateral triangular faces
Answer
B. Tetrahedron
30
An actual length of 5 m of a room is represented by 25 mm length on drawing RF
will be
Answer
B. 1 : 200
31
The amount of water held in the soil after excess gravitational water has been
drained
Answer
C. Field capacity
32
The Canal located outside the command area meant primarily to convey water from
one source of supply to another within the same
Answer
A. Feeder Canal
33
The structure constructed at the off take of the canal adjacent to the river under
sluice
Answer
D. Head Regulator
34
The usual capacity of tube well is _________ cumecs.
Answer
D. 0.040
35
Duty of an irrigation tube well is _________ than that of a canal irrigation.
Answer
A. Higher
36
The property of a fluid which offers resistance to the movement of one layer of fluid
over another layer of fluid
Answer
B. Viscosity
37
The rate of increase of pressure in a vertical direction equal to weight density of fluid
at that point
Answer
C. Hydrostatic Law
38
Piezometer is used for measuring
Answer
B. Pressure
39
The type of flow in which the fluid characteristics like velocity, pressure, density etc.
do not change with time
Answer
A. Steady flow
40
Command used to remove the selected object from a drawing
Answer
B. Erase
41
Which command create a new objects parallel to the original object ?
Answer
B. Offset
42
Which command draw line that extends infinity in both direction ?
Answer
C. X Line
43
Brick walls are measured in M2 if the thickness of the wall is
Answer
A. 10 cm
44
According to Indian Standard Institute the actual size of modular brick is
Answer
C. 19*9*9 cm
45
The measurement is not made in M2 ion case of
Answer
D. R. C. Chajja
46
Due to change in price level, a revised estimate is prepared if the sanctioned estimate
exceeds
Answer
D. 5%
47
While preparing a detailed estimate area should be measured correct to
Answer
A. .01 M2
48
A _________ is a set of rules that specify the standard for constructed objects such
as buildings and non-building structures.
Answer
A. Building Code
49
Combination of two or more plots as a single plot is called
Answer
A. Amalgamation
50
The property by which lime will set in damp place
Answer
B. Hydraulicity
51
The deformation per unit length is called
Answer
B. Strain
52
The unit of force in CGS system of unit is called
Answer
A. Dyne
53
Two forces act at an angle of 120°. If the greater force is 50 Kg and their resultant
is perpendicular to the smaller force, the smaller force is
Answer
B. 25 Kg
54
The moment of inertia of a circular lamina of diameter d about an axis perpendicular to the plane of the lamina and passing through its centre is:
Answer
D. πd⁴/32
55
Two loads of 50 kg and 75 kg are hung at the ends of a rope passing over a smooth
pulley shown in figure below. The tension in the string is
Answer
D. 60 kg
56
A body of weight 300 KN is placed on a horizontal plane. If the coefficient of friction
between the body and the horizontal plane is 0.25. Determine the horizontal force
required to just slide the body
Answer
C. 75 KN
57
The forces whose line of action lie on the same lines are known as
Answer
B. Collinear forces
58
A dimension is stated as 28 � 0.02 mm in a drawing. What is the tolerance ?
Answer
D. 0.04 mm
59
Which of the following is not the correct method of expressing a Fit under BIS system
of limits and fits ?
Answer
B. 50 g7/H8
60
Identify the Pneumatic symbol.
Answer
C. Hydraulic motor
61
Telescopic gauge is used for
Answer
A. Measuring inside size of slots or holes
62
In a M20 thread, M denotes
Answer
A. Metric
63
The least count of Vernier bevel protractor is
Answer
C. 5�
64
The minimum edge distance for rivets of diameter
Answer
C. 1.5d
65
A heat engine converts the heat energy from fuel combustion or any other source
into which type of work ?
Answer
B. Mechanical work
66
The ignition quality of petrol is expressed by
Answer
B. Octane number
67
General gas equation is
Answer
B. pv = mRT
68
A system which is completely uninfluenced by the surrounding is called
Answer
C. lsolated System
69
When a process are performed on a system in such a way that the final state is
identical with initial state known as
Answer
B. Thermodynamic cycle
70
The extension line should extend 3 mm beyond the
Answer
C. Dimension line
71
The amount of heat absorbed to evaporate 1 Kg of water from its saturation
temperature, without change of temperature, is called
Answer
B. Latent heat of vaporization
72
lf petrol is used in a diesel engine, then
Answer
C. Higher knocking will occur
73
When the whole body is sectioned at its middle, then the sectional view is obtained is
Answer
B. Full section
74
The formula for finding the volume of a solid sphere is
1 3 4 3
Answer
B. �r
3 3
3 3 4 2
75
If x + y = 32 and x – y = 10, then the value of x is
Answer
D. 21
76
Find the mean in the numbers 18, 22, 15, 32, 10, 23, 20.
Answer
A. 20
77
A pyramid with a square base has __________ Faces.
Answer
B. 5
78
Melting point of ice is
Answer
D. 32°F
79
If the circumference of the square is 16 cm then the area of the same is
_______ cm2.
Answer
A. 16
80
The lateral development of a cylinder is of __________ shape.
Answer
D. Rectangle
81
In a cabinet type of oblique projection, the receding edge is taken as
Answer
A. Half
82
When a 10 cm line in a drawing represents a 5 cm edge of an actual object then the
scale of drawing is
Answer
D. 2 : 1
83
Lines of hidden edges are drawn with
Answer
B. Dashed lines
84
lf a line is inclined at 45° to the HP and 30° to the VP, its front view is inclined at
Answer
D. Greater than 45°
85
What is the nominal shape of septic tank ?
Answer
C. Rectangle
86
Which gas is mainly produced in septic tank ?
Answer
D. Hydrogen sulphide
87
Which type of trap is used in Indian water closet ?
Answer
B. P Trap
88
What is the first stage in sewage treatment process ?
Answer
C. Screening
89
Which device is used to prevent sewer gases from entering the building ?
Answer
D. Trap
90
What is the name of the water coming out of the kitchen, bathroom, wash basin ?
Answer
A. Sullage
91
Poise is the unit of
Answer
C. Viscosity
92
Mass per unit volume is known as
Answer
B. Density
93
Manometer is a device used for measuring
Answer
A. Pressure at any point in a fluid
94
The increase of temperature
Answer
B. Decrease the viscosity of liquid
95
Pitot Tube is used for measurement of
Answer
D. Fluid flow velocity
96
A Francis Turbine is
Answer
D. A reaction radial flow turbine
97
An object situated in first quadrant, that means
Answer
C. Above HP and in front of VP
98
The Standard size of D3 Drawing board is
Answer
D. 500 × 350 × 15 mm
99
Dodecahedron is a solid having __________ equal and regular pentagons.
Answer
C. 12
100
The view drawn by taking actual dimension without preparing isometric scale is
called
Answer
A. Isometric View
Discussion
Ask a doubt or share a tip.
No comments yet — start the discussion.