| Post Name | Workshop Attender Draftsman Civil - Industrial Training |
|---|---|
| Question Paper Code | 022/2026/OL |
| Category Code | 256/2024 |
| Date of Test | 11 February 2026 |
| Exam Type | Online Examination |
| Total Questions | 100 |
1
A French curve is used for
Answer
C. Drawing irregular curves
2
What is the designation of 420 Ā“ 594 mm size paper as per BIS?
Answer
B. A2
3
What is the description of E1 hidden outlines?
Answer
A. Dashed Thick
4
In a drawing letters and numerals are designated by their
Answer
B. Height
5
How the unidirectional system dimensions are placed in engineering drawing to read?
Answer
D. From bottom of the drawing
6
Diagonal scale is constructed to measure upto ____________ units
Answer
C. 3 Units
7
In isometric projection, the angle between the axes is
Answer
D. 120 degree
8
Eccentricity of ellipse is
Answer
B. Less than 1
9
Providing good outside views from rooms refers to
Answer
B. Prospect
10
What percentage of plinth area is provided for horizontal circulation area?
Answer
B. 10 to 15%
11
Group E buildings are classiļ¬ed as?
Answer
A. Business building
12
Built up covered area measured at the ļ¬oor level is
Answer
C. Plinth area
13
The multiplying factor applied in painting work for fully glazed door is
Answer
B. 1 times one surface area for both sides
14
The percentage added for contractors proļ¬t while preparing abstract estimate is
Answer
B. 10%
15
Which is the accurate estimate prepared by working out quantities for each items of work
Answer
D. Detailed estimate
16
While taking quantity in a masonry work no deduction for opening, bearing etc...upto the area
Answer
A. 1000 cm2
17
The carpet area of a habitable room shall not be less than
Answer
C. 9.5 m2
18
The site plan shall be drawn to a scale of not less than
Answer
D. 1:400
19
Which is the unit of measurement of honey comb brick wall
Answer
B. m2
20
The value at the end of the utility period without being dismantled
Answer
A. Salvage value
21
How much percentage of alumina should contain in a good brick earth
Answer
B. 20-30
22
The colour of ordinary Portland cement should be
Answer
B. Greenish Grey
23
In the following which is the function of sand
Answer
D. All of the above
24
In following which is a retarder
Answer
C. Ammonium chloride
25
Which is the following is the natural defect in the timber
Answer
A. Shakes
26
The most eļ¬ective process of repairing concrete work which has damaged due to inferior work
Answer
C. Guniting
27
The mortar having bulk density of 15 KN/cubic mm or more are known
Answer
A. Heavy mortar
28
A ļ¬ne earthernware which is white thin and semi transparent
Answer
B. Porcelain
29
A solid substance is a ļ¬ne state of division and it forms the bulk of pain
Answer
D. Base
30
In the following which is the non-ferrous metal
Answer
A. Pig iron
31
What is the proportion of M15 grade concrete
Answer
D. 1:2:4
32
The slump test is used for determining
Answer
A. Work ability
33
A curved handrail ļ¬tting used to smoothly transition the hand rails height and angle
Answer
B. Gooseneck
34
The lower edges of the sloping roof are called
Answer
A. Eaves
35
A series of arches with intermediate supports is known as
Answer
A. Arcade
36
A course of stone provided immediately below the cornice is called
Answer
D. Frieze
37
Materials often used for damp prooļ¬ng is
Answer
C. Bitumen
38
The bearing capacity of a water logged soil can be improved by
Answer
B. Drainage
39
When a defective foundation is to be replaced the temporary structure adopted to support the building is
Answer
D. Underpinning
40
The length of a 45Ā° crank is
Answer
A. 0.42 D
41
The process of making permanent connection between two metal parts by heating them to molten state without application of any mechanical pressure is
Answer
C. Welding
42
The sloped underneath surface of a ļ¬ight is called
Answer
D. Soļ¬t
43
Which one of the following is a tension member
Answer
B. King post
44
The type of bond in which the bricks are laid in courses inclined at 45Ā° in two directions from center
Answer
A. Herring bone bond
45
Which of the following is an example of three centered arch
Answer
D. Elliptical arch
46
The depth of rebate is
Answer
C. 12 mm-15 mm
47
The slump desirable for footings and foundation is
Answer
A. 50-100 mm
48
Usually the crank is provided at a distance of ____________ from the support
Answer
C. L/5 - L/7
49
The vertical window provided on a sloped roof
Answer
B. Dormer window
50
An intermediate ļ¬oor between two ļ¬oors is
Answer
D. Mezzenine ļ¬oor
51
The cover for slab is
Answer
Question Cancelled
52
The ratio of M5 concrete is
Answer
C. 1:5:10
53
A machine that transforms rotational energy from a ļ¬uid that is picked by a rotor system into usable work or energy
Answer
A. Turbine
54
Hydro power is obtained from the generators coupled to water turbines which convert the hydraulic energy in to
Answer
D. Mechanical energy
55
A structure constructed on a channel to eļ¬ect a sudden change in the bed level of the channel is called
Answer
A. Canal fall
56
When seepage water is suļ¬cient for the growth of the crop and if no additional surface watering is necessary such detention dam is called
Answer
B. Water spread dam
57
Which irrigation method water is supplied to lower level by the action of gravity
Answer
C. Flow
58
The name of ļ¬rst watering before sowing the crop is called
Answer
A. Paleo
59
Which segment of GPS consist of satellite
Answer
A. Space
60
Which instrument is a combination of EDM, electronic theodolite and microprocessor
Answer
B. Total station
61
Which type is most common total stations used now a days
Answer
C. Automatic total stations
62
What is the name of measurement for distances taken to a prism on reļ¬ecting foil most accurate
Answer
D. Precise measurement
63
Which is an application of GPS for visually impaired
Answer
A. MOBIC
64
What is the length of a surveyor's chain
Answer
C. 66 Ft
65
The principles of chain surveying is
Answer
A. Triangulation
66
The book in which chain measurements are entered is called the ļ¬eld book. The size of ļ¬eld book is
Answer
D. 20 cm Ā“ 12 cm
67
The direction of a line relative to the given merdian is called
Answer
D. Bearing
68
Plane tabling is which method of surveying
Answer
A. Graphical
69
A closed contour line with one or more higher ones inside it represents a
Answer
B. Hill
70
The process of turning the telescope in horizontal plane is called
Answer
C. Swinging
71
The least count of levelling staļ¬ is
Answer
C. 5 mm
72
Which methods generally adopted for measuring the volume
Answer
D. All of the above
73
Which of the following is not a basic AUTOCAD command for drawing?
Answer
C. Delete
74
Which function key is used to cycle through object snaps in AUTOCAD?
Answer
B. F3
75
Consider the following statements about AUTOCAD Shortcuts: (i) Ctrl+Z is used for undo (ii) Ctrl+Y is used for Redo (iii) Ctrl+Shift+C is used for copying objects Which of the following options is correct?
Answer
D. All of the above (i, ii and iii)
76
In AUTOCAD, which tab is used to set up the paper size and orientation for printing?
Answer
B. Layout
77
Which AUTOCAD command allows you to create a 3D solid by revolving a 2D proļ¬le around an axis?
Answer
B. REVOLVE
78
In AUTOCAD, which command is used to set the scale, paper size and plot style before printing a drawing?
Answer
C. PAGESETUP
79
Which command is used to create a continuous sequence of connected lines or arcs in AutoCAD?
Answer
A. POLYLINE
80
In AUTOCAD, which command is used to create a 3D solid by sweeping a 2D proļ¬le along a path?
Answer
B. SWEEP
81
Which of the following is NOT a simple machine?
Answer
C. Gear
82
The SI unit of work is :
Answer
C. Joule
83
Which of the following is the correct formula for stress?
Answer
A. Force/Area
84
Consider the following statements about the perimeter of a rectangle: (i) The perimeter is calculated by adding all four sides (ii) The perimeter is calculated by multiplying length and width (iii) The perimeter is calculated by twice the sum of length and width Which of the following options is correct?
Answer
D. Both (i and iii)
85
Consider the following statements about trigonometric ratios in a right-angled triangle: (i) Cosec (q) is the reciprocal of sin (q) (ii) sec (q) is the reciprocal of cos (q) (iii) Cot (q) is the reciprocal of tan (q) Which of the following options is correct?
Answer
D. All of the above (i, ii and iii)
86
Consider the following statements about power and Energy : (i) Power is the rate at which work is done (ii) Energy is the capacity to do work (iii) Power and energy have the same SI unit. Which of the following options is correct?
Answer
C. Both (i and ii)
87
Who give the ļ¬rst scientiļ¬c thinking in highway construction which became the foundation of modern roads?
Answer
C. John Maccadam
88
The city roads which are primarly for through traļ¬c on a continuous route with a high level traļ¬c?
Answer
A. Arterial streets
89
The motor vehicle act was inacted in?
Answer
B. 1939
90
The longitudinal movement of rail is
Answer
D. Creep
91
The rail section is designated by its
Answer
C. Weight per metre length
92
Sleeper density is
Answer
B. The number of sleeper per rail length
93
The sleepers which satisfy all of the requirements and are suitable for track circuiting are
Answer
C. Wooden sleeper
94
For which type of wing wall the splay is 90 degree?
Answer
B. Return wing wall
95
The detention time for an ordinary plain sedimentation tank is
Answer
C. 4 to 8 hours
96
Which method is adopted for removing bushes, branches etc from water?
Answer
D. Screening
97
The suitable layout of a distribution system for well planned cities
Answer
A. Ring system
98
In which of the following method diļ¬erent types of refuses are collected, carried and disposed oļ¬ separately?
Answer
B. Conservancy system
99
Manholes are provided at every
Answer
D. All of the above
100
The sludge digestion process in a septic tank is
Answer
B. Anaerobic
Discussion
Ask a doubt or share a tip.
No comments yet ā start the discussion.